802.11r WiFi roaming configuration example: Difference between revisions
No edit summary |
No edit summary |
||
| Line 2: | Line 2: | ||
==Introduction== | ==Introduction== | ||
This article provides a basic configuration example of WiFi roaming. | This article provides a basic configuration example of 802.11r WiFi roaming. | ||
==Firmwware== | ==Firmwware== | ||
| Line 9: | Line 9: | ||
==Prerequisites== | ==Prerequisites== | ||
* Main gateway with WAN access (Any RUTOS router. RUTX50 is used in this example) | * Main gateway with WAN access (Any RUTOS router. RUTX50 is used in this example) | ||
* Access Points (Any WiFi-capable RUTOS device. RUTX11 (Router 1) and | * Access Points (Any WiFi-capable RUTOS device. RUTX11 (Router 1) and RUTX11 (Router 2) are used in this example) | ||
Before you start configuring the router <b>turn on "Advanced WebUI" mode</b>. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI. | Before you start configuring the router <b>turn on "Advanced WebUI" mode</b>. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI. | ||
| Line 17: | Line 17: | ||
==Configuration== | ==Configuration== | ||
[[File:Networking rutos configuration examples wifi roaming configuration scheme v2.png|border|class=tlt-border]] | |||
===Gateway router=== | |||
---- | |||
# Login to the router's WebUI, navigate to the '''Network → Interfaces → Edit LAN''' page. Enter main gateway's IP address and save. We will leave it default (192.168.1.1) for this example. | |||
<ol> | |||
<li>Connect your AP/WiFi router to the gateway router using LAN to LAN connection.</li> | |||
<li>Login to the router's WebUI, navigate to the '''Network → Interfaces → Edit LAN''' page. Configure as follows:</li> | |||
<ol> | |||
<li>Enter IP address on the same subnet as main gateway. We will use 192.168.1.2 for Router 1 and 192.168.1.3 for Router 2 in this example.</li> | |||
<li>Enter <b>IPv4 gateway</b>. We will use our gateway router's IP - 192.168.1.1.</li> | |||
<li>Disable <b>DHCP server</b>.</li> | |||
</ol> | |||
</ol> | |||
Revision as of 04:56, 26 September 2024
Introduction
This article provides a basic configuration example of 802.11r WiFi roaming.
Firmwware
The information in this page is updated in accordance with 00.07.09 firmware version. .
Prerequisites
- Main gateway with WAN access (Any RUTOS router. RUTX50 is used in this example)
- Access Points (Any WiFi-capable RUTOS device. RUTX11 (Router 1) and RUTX11 (Router 2) are used in this example)
Before you start configuring the router turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.
Configuration
Gateway router
- Login to the router's WebUI, navigate to the Network → Interfaces → Edit LAN page. Enter main gateway's IP address and save. We will leave it default (192.168.1.1) for this example.
- Connect your AP/WiFi router to the gateway router using LAN to LAN connection.
- Login to the router's WebUI, navigate to the Network → Interfaces → Edit LAN page. Configure as follows:
- Enter IP address on the same subnet as main gateway. We will use 192.168.1.2 for Router 1 and 192.168.1.3 for Router 2 in this example.
- Enter IPv4 gateway. We will use our gateway router's IP - 192.168.1.1.
- Disable DHCP server.