DHCP RELAY over L2TPv3: Difference between revisions
No edit summary |
mNo edit summary |
||
| Line 17: | Line 17: | ||
=== DHCP Pool === | === DHCP Pool === | ||
Login to the router's WebUI and navigate to '''Network → Interfaces → Ethernet LAN.''' Click the '''<nowiki/>'Edit'''' button on the right side of the interface to set the LAN network address. | |||
[[File:Server new 01 fixed.png|border|class=tlt-border|750x750px]] | [[File:Server new 01 fixed.png|border|class=tlt-border|750x750px]] | ||
Under '''DHCP SERVER''' set parameters for the DHCP pool. | Under '''DHCP SERVER''' set parameters for the DHCP pool. | ||
[[File:Server new 02 1 fixed.png|none|thumb]] | |||
===Set up Mobile WAN as Main WAN=== | ===Set up Mobile WAN as Main WAN=== | ||
Enter to the router’s WebUI, go to '''Network → Interfaces''' press mouse click on the Mobile Wan interface, then drag it to the 1<sup>st</sup> position and then press '''Save & Apply'''. | Enter to the router’s WebUI, go to '''Network → Interfaces''' press mouse click on the Mobile Wan interface, then drag it to the 1<sup>st</sup> position and then press '''Save & Apply'''. | ||
[[File:Server new 03.png| | [[File:Server new 03 fix.png|none|thumb]] | ||
===Create L2TPv3 instance=== | ===Create L2TPv3 instance=== | ||
Go to router’s WebUI, under '''Service → VPN → L2TP → L2TPv3''' and create new '''L2TPV3''' instance. | Go to router’s WebUI, under '''Service → VPN → L2TP → L2TPv3''' and create new '''L2TPV3''' instance. | ||
| Line 61: | Line 60: | ||
Layer 2 specific header type: Linux Default | Layer 2 specific header type: Linux Default | ||
[[File:Server new 04 01 fix.png|none|thumb]] | |||
[[File:Server new 04 01.png| | |||
[[File:Server new 04 02.png|alt=L2TPv3 Server Settings|center|thumb|480x480px|L2TPv3 Server Settings]]Specify the Local address of your mobile WAN. Local value for Tunnel ID, session ID and Cookie must match with the peer values being used at the other end. | [[File:Server new 04 02.png|alt=L2TPv3 Server Settings|center|thumb|480x480px|L2TPv3 Server Settings]]Specify the Local address of your mobile WAN. Local value for Tunnel ID, session ID and Cookie must match with the peer values being used at the other end. | ||
| Line 69: | Line 67: | ||
===DHCP Relay=== | ===DHCP Relay=== | ||
Enter the router's WebUI, go to '''Network → Interface → LAN → DHCP Server''' and change the "'''Enable DHCP'''" field value from Enable to Relay and type in the DHCP Server the IP address of the server. Click Save & Apply. | Enter the router's WebUI, go to '''Network → Interface → LAN → DHCP Server''' and change the "'''Enable DHCP'''" field value from Enable to Relay and type in the DHCP Server the IP address of the server. Click Save & Apply. | ||
[[File:Client 01.png| | [[File:Client 01 fix.png|none|thumb]] | ||
'''Note:''' The IPv4 address of the LAN interface is different from the server's LAN interface address, this is necessary to avoid conflicts. | '''Note:''' The IPv4 address of the LAN interface is different from the server's LAN interface address, this is necessary to avoid conflicts. | ||
===Set up Mobile WAN as Main WAN=== | ===Set up Mobile WAN as Main WAN=== | ||
Enter to the router’s WebUI, go to '''Network → Interfaces''' press mouse click on the Mobile Wan interface, then drag it to the 1<sup>st</sup> position and then press '''Save & Apply'''. | Enter to the router’s WebUI, go to '''Network → Interfaces''' press mouse click on the Mobile Wan interface, then drag it to the 1<sup>st</sup> position and then press '''Save & Apply'''. | ||
[[File:Client 02.png| | [[File:Client 02 fix.png|none|thumb]] | ||
===Modify Enable-DHCP-renew firewall rule=== | ===Modify Enable-DHCP-renew firewall rule=== | ||
Enter in the router’s WebUI, go to '''Network → Firewall → Traffic rules''' to additionally allow destination port 67. | Enter in the router’s WebUI, go to '''Network → Firewall → Traffic rules''' to additionally allow destination port 67. | ||
| Line 112: | Line 109: | ||
Layer 2 specific header type: Linux Default | Layer 2 specific header type: Linux Default | ||
[[File:Client 04.png| | [[File:Client 04 fix.png|none|thumb|747x747px]] | ||
[[File:Server new 04 02.png|alt=L2TPv3 Client Settings|center|thumb|523x523px|L2TPv3 Client Settings]] | [[File:Server new 04 02.png|alt=L2TPv3 Client Settings|center|thumb|523x523px|L2TPv3 Client Settings]] | ||
| Line 118: | Line 115: | ||
==Testing DHCP over L2TPv3== | ==Testing DHCP over L2TPv3== | ||
To test the realy settings go to DHCP server to check that devices are able to recieve IP addresses in the range 192.168.10.150 - 192.168.10.170 either via LAN port or Wi-Fi. Access the CLI and run '''cat /tmp/dhcp.leases''' to list all DHCP clients. | To test the realy settings go to DHCP server to check that devices are able to recieve IP addresses in the range 192.168.10.150 - 192.168.10.170 either via LAN port or Wi-Fi. Access the CLI and run '''cat /tmp/dhcp.leases''' to list all DHCP clients. | ||
[[File:Test 01.png| | [[File:Test 01 fix.png|none|thumb]] | ||
Asking for the Address Resolution Protocol (ARP) table is also an other method to find hosts on the LAN network. | Asking for the Address Resolution Protocol (ARP) table is also an other method to find hosts on the LAN network. | ||
[[File:Test 02.png| | [[File:Test 02 fix.png|none|thumb]] | ||
Revision as of 22:33, 25 March 2022
Main Page > General Information > Configuration Examples > Use cases > DHCP RELAY over L2TPv3Introduction
A DHCP relay agent allows the DHCP clients to obtain IP addresses from a DHCP server that is not configured on the same LAN.
This article provides a configuration example with details on how to set-up a DHCP relay over a L2TPv3 VPN.
Prerequisites
You will need:
- Two RUT or RUTX devices (one as Server and other as Client)
- A PC acting as a Host for testing
- Both routers must have a Public Static or Public Dynamic IP addresses
Configuration Scheme
I will paste a Topology Image here
DHCP Server Settings
DHCP Pool
Login to the router's WebUI and navigate to Network → Interfaces → Ethernet LAN. Click the 'Edit' button on the right side of the interface to set the LAN network address.
Under DHCP SERVER set parameters for the DHCP pool.
Set up Mobile WAN as Main WAN
Enter to the router’s WebUI, go to Network → Interfaces press mouse click on the Mobile Wan interface, then drag it to the 1st position and then press Save & Apply.
Create L2TPv3 instance
Go to router’s WebUI, under Service → VPN → L2TP → L2TPv3 and create new L2TPV3 instance.
LOCAL SETTING
Local address: 84.15.155.201
Tunnel ID: 100
Session ID: 100
Cookie: 12ABCDEF
PEER SETTING
Peer address: 84.15.249.182
Peer Tunnel ID: 10
Peer Session ID: 10
Peer Cookie: 12ABCDEF
INSTANCE SETTING
Bridge to: LAN
MTU: 1500
Encapsulation: IP
Layer 2 specific header type: Linux Default
Specify the Local address of your mobile WAN. Local value for Tunnel ID, session ID and Cookie must match with the peer values being used at the other end.
DHCP Client Settings (Relay)
DHCP Relay
Enter the router's WebUI, go to Network → Interface → LAN → DHCP Server and change the "Enable DHCP" field value from Enable to Relay and type in the DHCP Server the IP address of the server. Click Save & Apply.
Note: The IPv4 address of the LAN interface is different from the server's LAN interface address, this is necessary to avoid conflicts.
Set up Mobile WAN as Main WAN
Enter to the router’s WebUI, go to Network → Interfaces press mouse click on the Mobile Wan interface, then drag it to the 1st position and then press Save & Apply.
Modify Enable-DHCP-renew firewall rule
Enter in the router’s WebUI, go to Network → Firewall → Traffic rules to additionally allow destination port 67.
Create L2TPv3 instance
Go to router’s WebUI, under Service → VPN → L2TP → L2TPv3 and create new L2TPV3 instance.
LOCAL SETTING
Local address: 84.15.249.182
Tunnel ID: 10
Session ID: 10
Cookie: 12ABCDEF
PEER SETTING
Peer address: 84.15.155.201
Peer Tunnel ID: 100
Peer Session ID: 100
Peer Cookie: 12ABCDEF
INSTANCE SETTING
Bridge to: LAN
MTU: 1500
Encapsulation: IP
Layer 2 specific header type: Linux Default
Testing DHCP over L2TPv3
To test the realy settings go to DHCP server to check that devices are able to recieve IP addresses in the range 192.168.10.150 - 192.168.10.170 either via LAN port or Wi-Fi. Access the CLI and run cat /tmp/dhcp.leases to list all DHCP clients.
Asking for the Address Resolution Protocol (ARP) table is also an other method to find hosts on the LAN network.
