Domnev

From Teltonika Networks Wiki
Revision as of 14:32, 28 February 2023 by Domnev (talk | contribs)

The information in this page is updated in accordance with 00.07.03.4 firmware version .

Introduction

This article contains instructions on how to setup BACnet on Teltonika Networks devices.

Configuration overview and prerequisites

Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.

Prerequisites:

  • RUT955;
  • BACnet controller;
  • Server;
  • An end device (PC, Laptop, Tablet, Smartphone) for configuration;

If you're having trouble finding any page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode," which is located at the top-right corner of the WebUI.

Note: It is a additional software that can be installed from the Services → Package Manager page.

BACnet

BACnet


Install the BACnet package on RUT955 and navigate to Services → BACnet and enable (1) the instance. Everything else can be left as default or changed according to your needs.

Server


For the server, Yet Another BACnet Explorer (YABE) is used. Open the software and click on the green plus sign to add a new device. Then a new window will pop up, there select local endpoint IP address and leave everything else as default or change according to your needs.

File:Yabe configuration add device.png

Select newly created communication node and right - click on it to send WhoIs request (application might send these automatically).

<<SCREENSHOT>>

Results


In case of success you see the connected BACnet device and its parameters.

<<SCREENSHOT>>

BACnet/IP configuration

This is the most commonly used type of BACnet, which is designed to work over Ethernet networks using the Internet Protocol (IP). It supports both IPv4 and IPv6 addressing.

Router 1


BACnet


Install the BACnet package on RUT955 and navigate to Services → BACnetenable the instance and BBMD. Everything else can be left as default or changed according to your needs.

<<SCREENSHOT>>

Firewall


The configuration will also require you to add port forward rule in the firewall configuration. To do that, open Router1 WebUI and navigate to Network → Firewall → Port Forwards. Create a port forward rule to forward UDP packets from Router2 WAN to Router1 LAN address port.

<<SCREENSHOT>>

Note: When YABE sends registration packets you will need to find out which port YABE is using (One way is to look through the traffic with wireshark on your PC or TCP dump on router 1 or router 2)

If you restart YABE software or delete and create new communication device, YABE might use different port number, and you will need to change port forward configured in router connected to your PC.

Server


Open YABE and create IP communication node by click on add device.

<<SCREENSHOT>>

Then select the node and go to Meniu → Functions → IP services → Foreign device registration and enter public IP address of Router2 (the one connected to controller).

<<SCREENSHOT>>

Router 2


BACnet


Install the BACnet package on RUT955 and navigate to Services → BACnetenable the instance and BBMD. Everything else can be left as default or changed according to your needs.

<<SCREENSHOT>>

Firewall


The configuration will also require you to add port forward rule in the firewall configuration. To do that, open Router1 WebUI and navigate to Network → Firewall → Port Forwards. Create a port forward rule to forward UDP packets from Router2 WAN to Router1 LAN address port.

<<SCREENSHOT>>

Note: When YABE sends registration packets you will need to find out which port YABE is using (One way is to look through the traffic with wireshark on your PC or TCP dump on router 1 or router 2)

If you restart YABE software or delete and create new communication device, YABE might use different port number, and you will need to change port forward configured in router connected to your PC.

Server


Open YABE and create IP communication node by click on add device.

<<SCREENSHOT>>

Then select the node and go to Meniu → Functions → IP services → Foreign device registration and enter public IP address of Router2 (the one connected to controller).

<<SCREENSHOT>>

Results


In case of success you see the device connected via gateway.

<<SCREENSHOT>>

See also

BACnet on RUT955

External links

Yabe