569
edits
Changes
no edit summary
<p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.4'''] firmware version .</p>
==Introduction==
==Introduction==
* On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
* On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
* After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
* After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
[[File:Network RUTOS manual lan as wan vlan.png|border|class=tlt-border|1102px]]
[[File:VLAN config.png|border|center|class=tlt-border|798x239px]]
===Add new WAN interface===
===Add new WAN interface===
----
----
* Enter new <strong>Interface Name</strong>.
* Enter new <strong>Interface Name</strong>.
* Click on <strong>Add</strong> button.
* Click on <strong>Add</strong> button.
[[File:Network RUTOS manual lan as wan create interface.png|border|class=tlt-border|1102px]]
[[File:New interface.png|border|center|class=tlt-border|901x453px]]
----
----
* Choose <strong>DHCP</strong> Protocol from drop-down list.
* Choose <strong>DHCP</strong> Protocol from drop-down list.
* Press on <strong>Switch Protocol</strong>.
* Press on <strong>Switch Protocol</strong>.
[[File:Network RUTOS manual lan as wan interface setup dhcp.png|border|class=tlt-border|1102px]]
[[File:DHCP settings.png|border|center|class=tlt-border|870x261px]]
If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify:
If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify:
* IPv4 address
* IPv4 address
* IPv4 broadcast
* IPv4 broadcast
* DNS servers
* DNS servers
[[File:Network RUTOS manual lan as wan interface setup static_v2.png|border|class=tlt-border|1102px]]
[[File:Static IP.png|border|center|class=tlt-border|848x351px]]
----
----
After switching protocol More setting options will appear.
After switching protocol More setting options will appear.
* Go to <strong>Physical Settings</strong>.
* Go to <strong>Physical Settings</strong>.
* From drop-down list choose previously created VLAN interface (in this example it is eth0.300)
* From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
* Press <strong>Apply & Save</strong>.
* Press <strong>Apply & Save</strong>.
[[File:Network RUTOS manual lan as wan interface physical settings.png|border|class=tlt-border|1102px]]
[[File:Physical interface.png|border|center|class=tlt-border|866x281px]]
===Set/Check Firewall===
===Set/Check Firewall===
Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone.
Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone.
In WAN zone settings
In WAN zone settings
* Make sure that yours newly created interface is selected in Covered networks list.
* Make sure that yours newly created interface is selected in Covered networks list.
* Click Save & Apply.
* Click Save & Apply.
[[File:Network RUTOS manual lan as wan firewall zone.png|border|class=tlt-border|1102px]]
[[File:Firewall zones.png|border|center|class=tlt-border|859x422px]]
==Check new WAN interface==
==Check new WAN interface==
<li>Plug the main WAN cable back in and wait a bit. Refresh the website; the IP should have change back to the one shown in the first place.</li>
<li>Plug the main WAN cable back in and wait a bit. Refresh the website; the IP should have change back to the one shown in the first place.</li>
</ul>
</ul>
[[Category:LAN]]
[[Category:Update | hidden=yes]]
