Changes

LAN as WAN RutOS (view source)

Revision as of 13:06, 6 January 2022

736 bytes added ,  13:06, 6 January 2022
no edit summary
Line 2: Line 2:  
==Introduction==
 
==Introduction==
   −
This article contains instructions on how to set up LAN port as WAN on RUTOS if you have a need for multiple wired WAN connections.
+
This article contains instructions on how to set up LAN port as WAN on RUTxxx if you have a need for multiple wired WAN connections.
    
[[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]]
 
[[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]]
 +
 +
==Configuration overview and prerequisites==
 +
 +
Before we begin, let's overview the configuration that we are attempting to achieve and the prerequisites that make it possible.
 +
 +
'''Prerequisites''':
 +
* One RUTxxx series router.
 +
* At least two wired Internet connections.
 +
* An end device for test the configuration.<br>
 +
 +
'''Configuration scheme:'''
 +
 +
[[File:Networking_rut955_configuration_examples_lan_port_as_wan_scheme_v1.png|border|class=tlt-border]]
    
==Setting up second WAN interface==
 
==Setting up second WAN interface==
   −
To change LAN port purpose to WAN you will have to perform changes in 3 different locations of {{{name}}} WebUI
+
To change LAN port purpose to WAN you will have to perform changes in 3 different locations of RUTxxx WebUI
    
===Creating additional VLAN===
 
===Creating additional VLAN===
Line 14: Line 27:     
Go to <strong>Network > VLAN</strong> section in device WebUI and perform following actions:
 
Go to <strong>Network > VLAN</strong> section in device WebUI and perform following actions:
−
# Create new <strong>VLAN ID</strong> by clicking <strong>ADD</strong> button.
+
* Create new <strong>VLAN ID</strong> by clicking <strong>ADD</strong> button.
−
# On VLAN ID: 1 (LAN interface), select <strong>Off</strong> from drop-down list, on port that you want to use as secondary WAN.
+
* On VLAN ID: 1 (LAN interface), select <strong>Off</strong> from drop-down list, on port that you want to use as secondary WAN.
−
# On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
+
* On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
−
# After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
+
* After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
 
[[File:Network RUTOS manual lan as wan vlan.png|border|class=tlt-border|1102px]]
 
[[File:Network RUTOS manual lan as wan vlan.png|border|class=tlt-border|1102px]]
   Line 24: Line 37:     
Go to <strong>Network > Interfaces</strong> WebUI section.
 
Go to <strong>Network > Interfaces</strong> WebUI section.
−
# Enter new <strong>Interface Name</strong>.
+
* Enter new <strong>Interface Name</strong>.
−
# Click on <strong>Add</strong> button.
+
* Click on <strong>Add</strong> button.
 
[[File:Network RUTOS manual lan as wan create interface.png|border|class=tlt-border|1102px]]
 
[[File:Network RUTOS manual lan as wan create interface.png|border|class=tlt-border|1102px]]
 
----
 
----
    
After doing that you will be redirected to new window to set up new interface, when there:
 
After doing that you will be redirected to new window to set up new interface, when there:
−
# Choose <strong>DHCP</strong> Protocol from drop-down list.
+
* Choose <strong>DHCP</strong> Protocol from drop-down list.
−
# Press on <strong>Switch Protocol</strong>.
+
* Press on <strong>Switch Protocol</strong>.
 
[[File:Network RUTOS manual lan as wan interface setup dhcp.png|border|class=tlt-border|1102px]]
 
[[File:Network RUTOS manual lan as wan interface setup dhcp.png|border|class=tlt-border|1102px]]
 +
If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify:
 +
* IPv4 address
 +
* IPv4 netmask
 +
* IPv4 gateway
 +
* IPv4 broadcast
 +
* DNS servers
 +
[[File:Network RUTOS manual lan as wan interface setup static.png|border|class=tlt-border|1102px]]
 
----
 
----
    
After switching protocol More setting options will appear.
 
After switching protocol More setting options will appear.
−
# Go to <strong>Physical Settings</strong>.
+
* Go to <strong>Physical Settings</strong>.
−
# From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
+
* From drop-down list choose previously created VLAN interface (in this example it is eth0.300)
−
# Press <strong>Apply & Save</strong>.
+
* Press <strong>Apply & Save</strong>.
 
[[File:Network RUTOS manual lan as wan interface physical settings.png|border|class=tlt-border|1102px]]
 
[[File:Network RUTOS manual lan as wan interface physical settings.png|border|class=tlt-border|1102px]]
   Line 49: Line 69:     
In WAN zone settings
 
In WAN zone settings
−
# Make sure that yours newly created interface is selected in Covered networks list.
+
* Make sure that yours newly created interface is selected in Covered networks list.
−
# Click Save & Apply.
+
* Click Save & Apply.
 
[[File:Network RUTOS manual lan as wan firewall zone.png|border|class=tlt-border|1102px]]
 
[[File:Network RUTOS manual lan as wan firewall zone.png|border|class=tlt-border|1102px]]
  
Retrieved from "https://wiki.teltonika-networks.com/view/Special:MobileDiff/87447"

Navigation menu