Changes

QSG RUT951 (view source)

Revision as of 16:32, 20 February 2024

398 bytes added ,  20 February
no edit summary
Line 157: Line 157:     
Detailed compliance information is available at the following internet address: [https://wiki.teltonika-networks.com/view/Certificates wiki.teltonika-networks.com/view/Certificates].
 
Detailed compliance information is available at the following internet address: [https://wiki.teltonika-networks.com/view/Certificates wiki.teltonika-networks.com/view/Certificates].
 +
 +
'''Hazardous (Classified) Locations'''
 +
 +
This device is classified to UL 121201 Ed. 9-2017 and CSA C22.2 No. 213-17 (R2022) standards and are suitable for use in Class 1, Division 2,
 +
Groups A, B, C and D, T4 and Class I, Zone 2, Group IIC, T4 classified Hazardous Locations.
 +
 +
Ambient temperature range: -40°C ≤ Ta ≤ +75°C.
 +
 +
Ingress Protection rating: IP30.
 +
 +
All input and output wiring must follow Class I, Division 2 and Class I, Zone 2 wiring methods (NEC Section 501.10(B) or CEC 18-152) and follow the authority
 +
having jurisdiction.
 +
 +
The following warnings and instructions apply:
 +
 +
'''WARNING''' – EXPLOSION HAZARD. DO NOT CONNECT OR DISCONNECT WHEN ENERGIZED.
 +
 +
Cet appareil est classé selon UL 121201 Ed. 9-2017 et CSA C22.2 No. 213-17 (R2022) et conviennent pour une utilisation en Classe 1, Division 2,
 +
Groupes A, B, C et D, T4 et Classe I, Zone 2, Groupe IIC, T4 emplacements classés dangereux.
 +
 +
Plage de température ambiante: -40°C ≤ Ta ≤ +75°C.
 +
 +
Indice de protection contre la pénétration: IP30.
 +
 +
Tout le câblage d'entrée et de sortie doit suivre les méthodes de câblage de Classe I, Division 2 et de Classe I, Zone 2 (NEC Section 501.10(B) ou CEC 18-152)
 +
et suivre l'autorité compétente.
 +
 +
Les avertissements et instructions suivants s'appliquent:
 +
 +
'''AVERTISSEMENT''' – RISQUE D’EXPLOSION. NE PAS BRANCHER NI DÉBRANCHER SOUS TENSION.
      Line 190: Line 220:  
|WiFi
 
|WiFi
 
|20 dBm
 
|20 dBm
 +
 +
'''FCC Radiation Exposure Statement:'''
 +
 +
This device complies with the relevant FCC RF radiation exposure limit set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20 cm from all persons.
 +
 +
'''ISED Canada Radiation Exposure Statement:'''
 +
 +
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
 +
 +
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR‐102 établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
 +
 
|}
 
|}
   Line 297: Line 338:  
</table>
 
</table>
   −
== Configure your computer (Windows) ==
+
{{Template: Configure_your_computer_LAN_Windows
 +
<!------------------------DEVICE----------------------->
 +
| name        = RUT951 
 +
}}
   −
<br>
+
 
−
<table>
+
{{Template: Configure_your_computer_WiFi_Windows
−
    <tr>
+
<!------------------------DEVICE----------------------->
−
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; margin: 10px; padding-bottom: 25px;">1. Ensure the Wireless network connection is Enabled. Go to Start — Control Panel — Network and Internet — Network and Sharing Center. Click on the '''Change adapter settings''' in the left panel, then right-click on Wireless Network Adapter, and select Enable.</td>
+
| name        = RUT951
−
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; width: 680px; margin: 10px; padding-bottom: 25px;">[[File:Configure_your_computer_step_1.png|right|600 px]]</td>
+
}}
−
    </tr>
  −
    <tr>
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-top: 25px;">2. Check if IP and DNS are obtained automatically. Right-click on Wireless Network Adapter and select Properties. Then select '''Internet Protocol Version 4''' and click Properties.
  −
<br>3. If not selected, check to '''obtain an IP address''' and '''obtain DNS server address automatically'''. Click OK.</td>
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-bottom: 25px; padding-top: 25px;">[[File:Configure_your_computer_step_2.png|right|500 px]]</td>
  −
    </tr>
  −
    <tr style="border: 1px solid #E8E8E8;">
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-top: 25px;">4. Connect to a wireless network by right-clicking on Wireless Network Adapter and selecting Connect.</td>
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-bottom: 25px; ; padding-top: 25px;">[[File:Configure_your_computer_step_3.png|right|600 px]]</td>
  −
    </tr>
  −
    <tr style="border: 1px solid #E8E8E8;">
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-top: 25px;">5. Choose the wireless network RUT951 **** from the list and click Connect. Enter the WiFi password located on the device's label.</td>
  −
        <td style="border-bottom: 1px solid #e8e8e8; vertical-align: top; padding-bottom: 25px; ; padding-top: 25px;">[[File:Configure_your_computer_step_4.png|right|400 px]]</td>
  −
    </tr>
  −
</table>
      
== Login to device ==
 
== Login to device ==
Retrieved from "https://wiki.teltonika-networks.com/view/Special:MobileDiff/104862...120462"

Navigation menu