QSG TAP100

From Teltonika Networks Wiki
Main Page > TAP Access Points > TAP100 > QSG TAP100

This Wiki page contains the online version of the Quick Start Guide (QSG) for the TAP100 Access Point. Here you will find an overview of the various components for TAP100 device, hardware installation instructions, first login information, device specifications, and general safety information. It is highly recommended to acquaint yourself with the Quick Start Guide before using the device.

Safety information

Before starting operating the device, please review recommendations and precautions to minimize the possibility of accidents. Safety precautions presented are supplementary and subject to the local safety regulations. When various operations are executed on the device, the user must fully follow the safety instructions and recommendations provided with the device.

General

Radio specifications
RF technologies Wi-Fi
Max RF power 20 dBm@W-iFi
Integrated antennas specifications
WiFi antenna 2x 2400~2500 MHz, peak gain < 4.9 dBi, omnidirectional
Bundled accessories specifications*
Power adapter Input: 0.5 A@100-240V VAC, Output: 52 VDC, 0.35A, 802.3af

* Order code dependant.


TAP100 access point must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.


CE Declaration of Conformity

[BG] Bulgarian С настоящото TELTONIKA NETWORKS декларира, че този TAP100 е в съответствие със съществените изисквания и други разпоредби на Директиви 2014/53/ЕU, 2011/65/ЕU, 2009/125/EC.
[HR] Croatian Ovim TELTONIKA NETWORKS izjavljuje da je ovaj TAP100 u skladu s bitnim zahtjevima i ostalim relevantnim odredbama Direktive 2014/53/EU, 2011/65/EU, 2009/125/EC.
[CZ] Czech Společnost TELTONIKA NETWORKS tímto prohlašuje, že tento TAP100 splňuje základní požadavky a další ustanovení směrnic 2014/53/EU, 2011/65/EU, 2009/125/EC.
[DK] Danish Undertegnede TELTONIKA NETWORKS erklærer herved, at følgende udstyr TAP100 overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU, 2011/65/EU, 2009/125/EC.
[NL] Dutch Hereby, TELTONIKA NETWORKS declares that this TAP100 is in compliance with the essential requirements and other relevant provisions of Richtlijnen 2014/53/EU, 2011/65/EU, 2009/125/EC.
[EE] Estonian Käesolevaga kinnitab TELTONIKA NETWORKS seadme TAP100 vastavust Direktiivide 2014/53/EU, 2011/65/EU, 2009/125/EC põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
[FI] Finish TELTONIKA NETWORKS vakuuttaa täten että TAP100 tyyppinen laite on Direktiivien 2014/53/EU, 2011/65/EU, 2009/125/EC oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
[FR] French TELTONIKA NETWORKS déclare par la présente que ce TAP100 est conforme aux exigences essentielles et autres dispositions des Directives 2014/53/EU, 2011/65/EU, 2009/125/EC.
[DE] German TELTONIKA NETWORKS erklärt hiermit, dass dieses TAP100 den grundlegenden Anforderungen und anderen Bestimmungen der Richtlinien 2014/53/EU, 2011/65/EU, 2009/125/EC entspricht.
[GR] Greek Η TELTONIKA NETWORKS δηλώνει ότι το παρόν TAP100 συμμορφώνεται με τις βασικές απαιτήσεις και άλλες διατάξεις των Οδηγιών 2014/53/ΕU, 2011/65/ΕU, 2009/125/EC.
[HU] Hungarian A TELTONIKA NETWORKS kijelenti, hogy ez a TAP100 megfelel a 2014/53/EU, 2011/65/EU, 2009/125/EC irányelvek alapvető követelményeinek és egyéb rendelkezéseinek.
[IE] Irish Leis seo, dearbhaíonn TELTONIKA NETWORKS go gcomhlíonann an TAP100 seo bunriachtanais agus forálacha ábhartha eile Threoir 2014/53/EU, 2011/65/EU, 2009/125/EC.
[IT] Italian Con la presente, TELTONIKA NETWORKS dichiara che questo TAP100 è conforme ai requisiti essenziali e ad altre disposizioni pertinenti della Direttive 2014/53/EU, 2011/65/EU, 2009/125/EC.
[LV] Latvian TELTONIKA NETWORKS ar šo paziņo, ka šis TAP100 atbilst pamatprasībām un citiem Direktīvas 2014/53/EU, 2011/65/EU, 2009/125/EC noteikumiem.
[LT] Lithuanian Šiuo dokumentu UAB TELTONIKA NETWORKS deklaruoja, kad šis TAP100 atitinka esminius reikalavimus ir kitas 2014/53/EU, 2011/65/EU, 2009/125/EC Direktyvų nuostatas.
[MT] Maltese TELTONIKA NETWORKS b'dan tiddikjara li dan TAP100 jikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet oħra tad-Direttivi 2014/53/EU, 2011/65/EU, 2009/125/EC.
[NO] Norwegian TELTONIKA NETWORKS erklærer herved at denne TAP100 er i samsvar med de grunnleggende kravene og andre bestemmelser i Direktivene 2014/53/EU, 2011/65/EU, 2009/125/EC.
[PL] Polish TELTONIKA NETWORKS niniejszym oświadcza, że niniejszy TAP100 jest zgodny z zasadniczymi wymaganiami i innymi postanowieniami Dyrektyw 2014/53/EU, 2011/65/EU, 2009/125/EC.
[PT] Portuguese A TELTONIKA NETWORKS declara que esta TAP100 cumpre os requisitos essenciais e outras disposições das Directivas 2014/53/EU, 2011/65/EU, 2009/125/EC.
[RO] Romanian TELTONIKA NETWORKS declară prin prezenta că acest TAP100 este în conformitate cu cerințele esențiale și cu alte dispoziții ale Directivelor 2014/53/EU, 2011/65/EU, 2009/125/EC.
[SK] Slovak Spoločnosť TELTONIKA NETWORKS týmto vyhlasuje, že tento TAP100 spĺňa základné požiadavky a ďalšie ustanovenia smerníc 2014/53/EU, 2011/65/EU, 2009/125/EC.
[SI] Slovenian TELTONIKA NETWORKS izjavlja, da je ta TAP100 skladen z bistvenimi zahtevami in drugimi določbami Direktiv 2014/53/EU, 2011/65/EU, 2009/125/EC.
[ES] Spanish TELTONIKA NETWORKS declara por la presente que este TAP100 cumple los requisitos esenciales y otras disposiciones de las Directivas 2014/53/EU, 2011/65/EU, 2009/125/EC.
[SE] Swedish TELTONIKA NETWORKS förklarar härmed att denna TAP100 uppfyller de grundläggande kraven och andra bestämmelser i Direktiven 2014/53/EU och 2011/65/EU, 2009/125/EC.

Detailed compliance information is available at the following internet address: wiki.teltonika-networks.com/view/Certificates.


This sign means that is necessary to read the User's Manual before you start using the device.

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.

Hereby, TELTONIKA NETWORKS declares that this TAP100 is in compliance with the essential requirements and other relevant provisions of Directives 2014/53/EU, 2011/65/EU, 2009/125/EC. The full text of the EU Declaration of Conformity is available at the following internet address: wiki.teltonika-networks.com/view/TAP100 _CE/RED

Hereby, TELTONIKA NETWORKS declares that this TAP100 is in compliance with Radio Equipment Regulations 2017, The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019. The full text of the UK Declaration of Conformity is available at the following internet address: wiki.teltonika-networks.com/view/TAP100_UKCA

RF exposure

This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies. The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits.

External antennas used with TAP100 must be installed to provide a distance of at least 20 cm from any people and must not be co-located or operated in conjunction with any other antenna or transmitter.

Any external antenna gain must meet RF exposure and maximum radiated output power limits of the applicable rule section.

Operating Frequency / Maximum transmission power
Wi-Fi 2.4 GHz 2412-2472 MHz, 20 dBm

Operating conditions

  • Operating temperature: -40° to +40° Celsius
  • Humidity should be in the range of 10% to 90% (non-condensing). Only use the device in dry environments.
  • Out of direct sunlight
  • Away from heat source, corrosive substances, salts, and flammable gases

Attention: operation outside the permissible range can considerably shorten the service life of the device.

Faulty and damaged products

  • Do not attempt to disassemble the device or its accessories.
  • Only qualified personnel must service or repair the device or its accessories.
  • If your device or its accessories have been submerged in water punctured or subjected to a severe fall, do not use until they have been checked at an authorized service center.

Electrical safety

  • Only use approved accessories.
  • Do not connect with incompatible products or accessories.
  • It is recommended to ground devices with grounding terminals before connecting them to power. Failure to ground appropriately might result in a shock hazard. The cross-sectional area of the protective grounding conductor should be at least 1mm2.

Product handling

  • You alone are responsible for how you use your device and any consequences related to its use.
  • Use of your device is subject to safety measures designed to protect users and their environment.
  • Always treat your device and its accessories with care and keep it in a clean and dust-free place.
  • Do not expose your device or its accessories to open flames, lit tobacco products, liquid, moisture, or high humidity.
  • Do not drop, throw or try to bend your device or its accessories.
  • Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.
  • Do not paint your device or its accessories.
  • Do not attempt to disassemble your device (exemptions for devices that require disassembly for SIM insertion) or its accessories: it does not contain any user-serviceable parts. For safety reasons, the equipment should be opened only by qualified personnel.
  • Make sure to use ESD personal protective equipment while the equipment is serviced.
  • Do not use your device in an enclosed environment where heat dissipation is poor.
  • Prolonged use in such space may cause excessive heat and raise ambient temperature, which will lead to the automatic shutdown of your device or the disconnection of the mobile network connection for your safety. To use your device again after such a shutdown, cool it in a well-ventilated place before turning it on.
  • Please check all national laws and local regulations for the disposal of electronic products.
  • Do not operate the device where ventilation is restricted.
  • Do not use or install this product near water to avoid fire or shock hazards.
  • Avoid exposing the equipment to rain or damp areas.
  • Arrange power and Ethernet cables so that they are not likely to be stepped on or have items placed on them.
  • Ensure that the voltage and the rated current of the power source match the device’s requirements. Do not connect the device to an inappropriate power source.
  • During a thunderstorm, no operations should be carried out on the device and cables.
  • The unit must be powered off where blasting is in progress and explosive atmospheres are present or near medical life support equipment.
  • Do not leave your device and its accessories within reach of small children or allow them to play with it. They could hurt themselves or others and could accidentally damage the device. Your device contains small parts with sharp edges that may cause an injury choking hazard.
  • Like any wireless device, this device operates using radio signals, which cannot guarantee connection in all conditions. Therefore, you must never rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data, or other loss.
  • The device may become warm during regular use.

Bottom view



AP Mounting Bracket Lock



TAP100 RJ45 Port

Video Quick Start Guide

Need some help setting up your new Teltonika Networks TAP10 Access Point? Watch our quick start guide video and follow the step-by-step instructions to set up your new access point for operation easily.



Installation Guide

Mounting instruction

1. Mount the AP Mounting Bracket using screws (not included). Mounting holes are Ø 4.6 cm. You can find more in TAP100 Spatial Measurements page.
2. Ensure the AP Mounting Bracket is secure and the Ethernet cable is ready.
3. Connect the LAN cable and orient the TAP100 RJ45 port at a 90-degree angle to the AP Mounting Bracket lock.
4. Turn the TAP100 counterclockwise to lock it onto the AP Mounting Bracket.

Login to device

1. Ensure that the TAP100 is connected to the Internet.

To access WebUI without an Internet connection follow this guide.

2. To access the TAP100 WebUI, type tap100.rutos.net into your browser. If you're unable to access the URL, try power cycling the TAP100.

3. When prompted for authentication enter the username admin and enter the password located on the device information label/engraving.

4. After logging in, you must set a new password for security reasons. You will not be able to interact with the access point’s WebUI until the default password is changed. The new password must consist of a minimum of 8 characters. Requirements: one uppercase letter, one lowercase letter, and one digit.

TAP100 Setup Without Internet Access

If you need to configure the TAP100 without an internet connection, please refer to the guide in this section.


1. Ensure the Wireless network connection is Enabled. Go to Start — Control Panel — Network and Internet — Network and Sharing Center. Click on the Change adapter settings in the left panel, then right-click on Wireless Network Adapter, and select Enable.
2. Right-click on Wireless Network Connection and select Properties. Then select Internet Protocol Version 4 and click Properties.

3. If not selected, check to Use the following IP address and enter 192.168.1.5.

4. Click in the Subnet mask it should get auto-filled with 255.255.255.0. Click OK.

5. Connect to a wireless network by right-clicking on Wireless Network Adapter and selecting Connect.
6. Choose the wireless network TAP100 **** from the list and click Connect. Enter the WiFi password located on the device's label.


7. To enter the router's Web interface (WebUI), type http://192.168.1.3 into the URL field of your Internet browser.

8. When prompted for authentication enter the username admin and enter the password located on the device information label/engraving.
Retrieved from "https://wiki.teltonika-networks.com/index.php?title=QSG_TAP100&oldid=114610"