RUT955 Failover

From Teltonika Networks Wiki
Main Page > RUT Routers > RUT955 > RUT955 Manual > RUT955 WebUI > RUT955 Network section > RUT955 Failover

The information in this page is updated in accordance with firmware version RUT9_R_00.07.04.5.
Note: click here for the old style WebUI (FW version RUT9XX_R_00.06.09.5 and earlier) user manual page.


This chapter is an overview of the Failover and Load Balancing functions in RUT955 device.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking rut9 manual webui basic advanced mode.gif


The Failover function allows you to backup your primary WAN connection in case it goes down.

In order to set priorities, simply press left mouse click on the interface, then drag it to the 1st, 2nd or other position and then press Save & Apply.

Networking rutos manual failover failover interfaces mobile 1 v1.png

You can drag & drop an interface in order to change its position on the list. Interfaces that are higher on the list have a higher priority than the ones that are lower, i.e., the device will always use the WAN interface with the highest priority as long as it is available. If it goes down, the device will start using the interface with the second highest priority and so on.

Take note that changing an interface's position in the list here also changes its position in the following pages:

Failover Interface Configuration

A failover Interface Configuration page is used to configure how the device will determine whether an interface is online or offline. To enter an interface configuration page, click the 'Edit' button next to an interface.

Networking rutos manual failover interface configuration edit button v1.png

After this you should be redirected to the configuration page of that interface.

Networking rutos manual failover interface configuration.png

Field Value Description
Enable off | on; default: off Turn the interface on or off.
Interval integer [1..65000]; default: 3 Number of seconds between each test
Flush connections on Connected | Disconnected: none Flushes established connections after the selected scenario occurs to renew the priorities of configured interfaces.
Method Ping | Wget; default: Ping Defines how health check will be performed on this interface when determining its state.
Track IP ip | hostname; default:, IP address(es) or hostname(s) that will be used to determine an interface's state. If the device receives no response from any of the specified hosts, the interface will be considered as 'Offline'. If this value is missing the interface is always considered up.
Reliability integer [1..65000]; default: 1 Number of hosts that must reply for the test to be considered successful. Make sure there are at least this many hosts defined in the 'Track IP' field, otherwise the interface will always be considered as 'Offline'.
Count integer [1..65000]; default: 1 Number of pings to send to each host with each test.
Up integer [1..65000]; default: 3 Number of successful tests required to considered an interface as 'Online'.
Down integer [1..65000]; default: 3 Number of failed tests required to considered an interface as 'Offline'.

Load Balancing

Load Balancing is a method of dividing traffic between multiple WAN interfaces. Load Balancing can be used to share the data load between different interfaces and increase the overall Internet speed for multiple users and connections. It is important to note that Load Balancing does not increase speed for any single connection. For example, if you're downloading a large file, using Load Balancing will not increase the speed of that download.

However, Load Balancing can be used to increase the speed of multiple connections. For example, when used in a WiFi network, Load Balancing would utilize the resources of multiple WAN interfaces to handle the many various requests of different clients.

Both Load Balancing and Failover cannot be used at the same time. If you wish to select Load Balancing, you can do that in the dropdown located in the top-right corner of the page:

Networking rutos manual failover load balancing select.png

Below is an example of the Load Balancing page.

Networking rutos manual failover load balancing interfaces.png

When Load Balancing is selected, you can assign ratio values to WAN interfaces. The ratio value represents a percentage of traffic load that will go through an interface. For example, if you set it up like this:

  • Wired WAN Ratio:
  • 3
  • Mobile WAN Ratio:
  • 2

    then about 60 % (3/5) of traffic would go through the Wired WAN interface and about 40 % (2/5) would go through Mobile WAN. In this case if you played 100 different videos on the Internet, about 60 would be downloaded through Wired WAN and the other 40 would be downloaded via Mobile WAN.


    A Load Balancing/Failover Rule is a set of conditions that define some type of network traffic. The traffic that matches the conditions set in the rule is handled in accordance to the specified Policy.

    There is one default rule present on the device. You can add more rules with the 'Add' button or you can customize the existing rule by clicking the 'Edit' button next to it:

    Networking rutos manual failover load balancing rules.png

    Networking rutos manual failover load balancing rule configuration.png

    Field Value Description
    Protocol all | tcp | udp | icmp | esp; default: all Protocol to match this rule.
    Source address ip/netmask; default: none Source IP addresses to match this rule.
    Destination address ip/netmask; default: Destination IP addresses to match this rule.
    Sticky off | on; default: off If turned on, traffic from the same source IP address that previously matched this rule within the sticky timeout period will use the same WAN interface.
    Sticky timeout integer [1..1000000]; default: 600 Timeout in seconds.
    Policy assigned default (Load Balancing) | default (Failover) | Unreachable (Reject) | Blackhole (Drop) | Default (Use main routing table) | custom; default: default (Failover) Selects the policy to apply to traffic that matches the conditions of this rule. You can create custom Load Balancing/Failover policies in the section below.


    A Policy dictates what the the device should do when some network traffic matches the condition defined in a Failover/Load Balancing rule. There are two policies by default, one for Load Balancing, the other for Failover. You may create custom policies that use different interfaces for Failover/Load Balancing scenarios.

    Networking rutos manual failover load balancing rules policies.png