RUTX09 Cloud Solutions

From Wiki Knowledge Base | Teltonika Networks
This is the approved revision of this page, as well as being the most recent.
Main Page > RUTX Routers > RUTX09 > RUTX09 Manual > RUTX09 WebUI > RUTX09 Services section > RUTX09 Cloud Solutions

The information in this page is updated in accordance with firmware version RUTX_R_00.02.04.1.

Summary[edit | edit source]

The Cloud Solutions section is used to configure how the device will connect to certain cloud management systems. This chapter is an overview of the Cloud Solutions section for RUTX09 routers.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking rutx manual webui basic advanced mode v1.gif

RMS[edit | edit source]

RMS (Remote Management System) is a cloud system designed by Teltonika and intended for remote monitoring and management of Teltonika-Networks products.

In order to add a device(s) to RMS, get yourself acquainted by watching this instructional video and register an account by clicking here. Each unique device receives a free month-long RMS license when added to RMS for the first time.


The figure below is a screenshot of the RMS section taken from a device which has been connected to RMS:

Networking rutx manual cloud solutions rms connected v1.png

Field Value Description
Connection type Enabled | Standby | Disabled; default: Enabled Defines how the device will connect to RMS:
  • Enabled - the device attempts to connect to RMS every 2-5 minutes (every 2 minutes the first hour; then every 5 minutes). If it cannot connect for 14 days, it will enter Standby mode.
  • Standby - the device attempts to connect to RMS every 6 hours.
  • Disabled - RMS functionality is disabled.
Hostname host | ip; default: rms.teltonika.lt Address of the RMS server. If you're using regular RMS, just leave the default address (rms.teltonika.lt).
Port integer [0..65535]; default: 15009 Port number for connecting to RMS. If you're using regular RMS, just leave the default port (15009).



The RMS server waits for incoming connections. Since the device attempts to connect at a fixed interval, it may not connect instantly after you add it to RMS. While it is disconnected, you can check how much time is left until the next connection attempt in the Status section:

Networking rutx manual cloud solutions rms disconnected v1.png To speed up the process by initiating an immediate connection attempt, click the 'Connect' button.

For more information on Teltonika's Remote Management System (RMS) refer to the RMS Manual or RMS FAQ pages.

Cumulocity[edit | edit source]

Cumulocity IoT is a cloud-based, real-time IoT management platform that's also compatible with Teltonika-Networks devices.

The figure and table below provides explanations for Cumulocity configuration parameters. For a detailed configuration guide, click here.

Networking rutos manual cloud solutions cumulocity modem 1.png

Field Value Description
Enable off | on; default: off Turns the Cumulocity service on or off.
Use SSL/TLS off | on; default: off Turn SSL/TLS protocol support on or off.
Server Address host; default: none Your Cumulocity server's hostname. It should match the Environment name from the Cumulocity registration.
For example: teltonika-networks.eu-latest.cumulocity.com
Interval integer; default: none Connection push interval in minutes. This field defines how often the device will try to connect to the Cumulocity server.
Mobile Interface network interface; default: mob1s1a1 Interface whose GSM parameters will be sent to the Cumulocity server for monitoring.
Reset Auth - (interactive button) Resets authentication for this device. If you click this, you'll have to authorize this from Cumulocity dashboard before it can successfully connect to the server.