RUTX09 UPNP

From Wiki Knowledge Base | Teltonika Networks
This is the approved revision of this page, as well as being the most recent.
Main Page > RUTX Routers > RUTX09 > RUTX09 Manual > RUTX09 WebUI > RUTX09 Services section > RUTX09 UPNP

The information in this page is updated in accordance with firmware version RUTX_R_00.02.04.1.

Summary[edit | edit source]

UPnP allows clients in the local network to automatically configure the router. This chapter is a summary of the UPnP function in RUTX09 routers.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking rutx manual webui basic advanced mode v1.gif

Active UPnP Redirects[edit | edit source]

Active UPnP Redirects sections allows you to manage currently active UPnP redirects.

Network rutx manual upnp redirects v1.png

MiniUPnP Settings[edit | edit source]

General Settings[edit | edit source]


Network rutx manual upnp general settings v1.png

field name value description
Enable off | on; default: off Toggles UPnP ON or OFF.
Use secure mode off | on; default: on Toggles Secure mode ON or OFF.
Enable additional logging off | on; default: off Puts extra debugging information into the system log when enabled.
Downlink integer; default: 1024 Bandwidth available for traffic coming in from the external interface in kilobytes per second. Note that this only information given to clients, it doesn't control the speed.
Uplink integer; default: 512 Bandwidth available for traffic out the external interface in kilobytes per second. Note that this only information given to clients, it doesn't control the speed.
Port integer [1..65535]; default: 5000 Toggles Secure mode ON or OFF.

Advanced Settings[edit | edit source]


Network rutx manual upnp advanced settings v2.png

field name value description
Report system instead of daemon uptime off | on; default: on If enabled, system service uptime is reported.
Device UUID string; default: unique The Device UUID attribute specifies and uniquely identifies a device that supports Universal Plug and Play (UPnP).
Announced serial number string; default: none Specifies serial number for XML Root Desc.
Announced model number string; default: none Specifies model number for XML Root Desc.
Notify interval integer; default: none Interval in which UPnP capable devices send a message to announce their services.
Clean ruler threshold integer; default: none Minimum number of redirections before clearing rules table of old (active) redirections.
Clean ruler interval integer; default: none Number of seconds before cleaning redirections.
Presentation URL string; default: none Presentation url used for the Root Desc.
UPnP lease file string; default: /var/run/miniupnpd.leases Stores active UPnP redirects in a lease file (specified), like DHCP leases.

MiniUPnP ACLs[edit | edit source]

ACLs specify which external ports may be redirected to which internal addresses and ports. There are two preconfigured rules, one to allow high ports, and another to deny the rest. Highest priority is at the top of a list and goes down. To add another specific rule press 'Add' button.

Network rutx manual upnp upnp acls v1.png

field name value description
Comment string; default: none Adds a comment to this rule.
External ports integer [0..65535] | range of integers [0-65535]; default: none External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers.
Internal Addresses ip/integer [0..32]; default: none Internal address to be redirect to.
Internal ports integer [0..65535] | range of integers [0-65535]; default: none Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers.
Action allow | deny; default: allow Allows or forbids the UPnP service to open the specified port.