RUTX14 WAN

From Teltonika Networks Wiki
Main Page > RUTX Routers > RUTX14 > RUTX14 Manual > RUTX14 WebUI > RUTX14 Network section > RUTX14 WAN

The information in this page is updated in accordance with firmware version RUTX_R_00.07.04.3.


Summary

The WAN page is used to to set up WAN network interfaces, which are used to connect device with external networks.

This manual page provides an overview of the WAN windows in RUTX14 devices.

WAN

The WAN section displays WAN network interfaces currently existing on this device.

Networking rutos manual wan mobile 1 dualsim 1 dualmodem 0 wired 1 v2.png

From here you can turn the interfaces on or off, change their priority* or enter an interface's configuration page.

* You can change the priority by dragging and dropping an interface to another position. Moving an interface changes its metric value in the configuration file. Interfaces that are higher on the list have greater priority.

Interface configuration

This section provides information on WAN interface configuration. There are two types of WAN interfaces on the device:

  • Ethernet WAN
  • Mobile WAN

Each supports different types of protocols and setups, which are described in the sections below.

To begin configuring an interface, click the 'Edit' button on the right side of the interface:

Networking rutos manual wan begin to edit eth 1 v2.png

Static

The static address protocol uses a predefined manual configuration instead of obtaining parameters automatically via a DHCP lease.

Static: General Settings

Networking rutos manual wan wan configuration general setup static address v2.png

Field Value Description
Hostname to send when requesting DHCP string; default: none A hostname for this interface used to identify this machine on the DHCP server.

Mobile

The Mobile protocol is used to set up an interface which can establish a mobile WAN connection.

Mobile: General Settings

Networking rutos manual wan mobile configuration general setup dualsim 1 dualmodem 0 v2.png

Field Value Description
Mode NAT | Bridge | Passthrough; default: NAT Mobile connection operating mode.
  • NAT - the mobile connection uses NAT (network address translation).
  • Bridge - bridges the LTE data connection with LAN. The device assigns its WAN IP address to another device (first connected to LAN or specified with MAC address). Using Bridge mode will disable most of the device’s capabilities.
  • Passthrough - in this mode the RUTX14 shares its WAN IP to a single LAN device (first connected to LAN or specified with MAC address). The LAN device will get WAN IP of RUTX14 instead of LAN IP. Using Passthrough mode will disable most of the device’s capabilities.
SIM SIM1 | SIM2; default: SIM1 Selects which SIM slot will be used for this interface.
Auto APN off | on; default: on The Auto APN feature scans an internal Android APN database and selects an APN based on the SIM card's operator and country. If the first automatically selected APN doesn't work, it attempts to use the next existing APN from the database.
APN / Custom APN string; default: none An Access Point Name (APN) is a gateway between a GSM, GPRS, 3G or 4G mobile network and another computer network. Depending on the contract, some operators may require you to use an APN just to complete the registration on a network. In other cases, APN is used to get special parameters from the operator (e.g., a public IP address) depending on the contract.
An APN Network Identifier cannot start with any of the following strings:
  • rac;
  • lac;
  • sgsn;
  • rnc;
it cannot end in:
  • .gprs;
and it cannot contain the asterisk symbol (*).
Bridge | Passthrough: MAC Address mac; default: none Specifies the MAC address of the device that will receive the mobile interface's IP address in Bridge or Passthrough mode.
Note: this field only becomes visible when using Bridge or Passthrough mode.

Mobile: Mobile Data Limit

The Mobile Data Limit section provides you with the possibility to set data usage limits for your mobile network interfaces and data usage warnings via SMS message in order to protect yourself from unwanted data charges.

In order to view the Mobile Data Limit section, the interface protocol must be set to Mobile.

Networking rutos manual wan mobile configuration mobile data limit.png

Field Value Description
Enable data connection limit off | on; default: off Turns mobile data limitations on or off.
Data limit* (MB) integer; default: 1000 The amount of data that is allowed to be downloaded over the specified period of time. When the limit is reached, the device will no longer be able to establish a data connection until the period is over or the data limit is reset.
Period Month | Week | Day; default: Day Data limit period after which the data counter is reset on the specified Start day.
Start day | Start hour day [1..31] | day [Monday..Sunday] | hour [1..24]; default: hour 0 Specifies when the period of counting data usage should begin. After the period is over, the limit is reset and the count begins over again.
Enable SMS warning off | on; default: off Turns SMS warning on or off. When turned on and configured, sends an SMS message to a specified number after the SIM card uses a specified amount of data.
Data limit* (MB) integer; default: none The received data limit before sending an SMS warning. After reaching using the the amount of data specified in this field, the router will send an SMS warning message to the specified phone number.
Phone number phone number; default: none Recipient's phone numbers.
Clear Collected Data - (interactive button) Clears the data limit counter.
Retrieved from "https://wiki.teltonika-networks.com/index.php?title=RUTX14_WAN&oldid=81790"