Changes

Template:Networking rutos manual wireless (view source)

Revision as of 16:07, 15 September 2023

1,415 bytes removed ,  16:07, 15 September 2023
no edit summary
Line 29: Line 29:  
|TCR100 = [[File:Networking_rutos_manual_wireless_wifi_5_tcr1_v3.png|border|class=tlt-border]]
 
|TCR100 = [[File:Networking_rutos_manual_wireless_wifi_5_tcr1_v3.png|border|class=tlt-border]]
 
|TAP100 = [[|border|class=tlt-border]]
 
|TAP100 = [[|border|class=tlt-border]]
−
|RUT241|RUT200|RUT951|RUT956|RUT906 = [[File:Networking rutos manual wireless wifi 2 v2 mixed.png|border|class=tlt-border]]
+
|RUT241|RUT200|RUT951|RUT956|RUT906|RUT901 = [[File:Networking rutos manual wireless wifi 2 v2 mixed.png|border|class=tlt-border]]
 
|#default = [[File:Networking_rutos_manual_wireless_wifi_{{{wifi}}}_v3.png|border|class=tlt-border]]
 
|#default = [[File:Networking_rutos_manual_wireless_wifi_{{{wifi}}}_v3.png|border|class=tlt-border]]
 
}}
 
}}
Line 48: Line 48:  
===={{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings====
 
===={{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings====
   −
The <b>{{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#ifeq:{{{series}}}|TAP100||by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#ifeq:{{{series}}}|TAP100|Radio|Wireless}} page:
+
The <b>{{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#ifeq:{{{series}}}|TAP100||by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#ifeq:{{{series}}}|TAP100|Radio page.|Wireless page:}}
−
 
   
{{#switch:{{{name}}}
 
{{#switch:{{{name}}}
 
|TAP100 =
 
|TAP100 =
 
|TCR1 = [[File:Networking_rutos_manual_wireless_global_settings_edit_button_tcr1_v3.png|border|class=tlt-border]]
 
|TCR1 = [[File:Networking_rutos_manual_wireless_global_settings_edit_button_tcr1_v3.png|border|class=tlt-border]]
−
|RUT241|RUT200|RUT951|RUT956|RUT906 = [[File:Networking rutos manual wireless wifi 2 v2 mixed.png|border|class=tlt-border]]
+
|RUT241|RUT200|RUT951|RUT956|RUT906|RUT901 = [[File:Networking rutos manual wireless wifi 2 v2 mixed.png|border|class=tlt-border]]
 
|#default = [[File:Networking_rutos_manual_wireless_global_settings_edit_button_v3.png|border|class=tlt-border]]
 
|#default = [[File:Networking_rutos_manual_wireless_global_settings_edit_button_v3.png|border|class=tlt-border]]
 
}}
 
}}
Line 259: Line 258:  
|TCR100 = [[File:Networking_rutos_manual_wireless_interface_configuration_edit_button_tcr1_v3.png|border|class=tlt-border]]
 
|TCR100 = [[File:Networking_rutos_manual_wireless_interface_configuration_edit_button_tcr1_v3.png|border|class=tlt-border]]
 
|TAP100 = [[File:Networking_rutos_manual_wireless_interface_configuration_edit_button_tap100_v3.png|border|class=tlt-border]]
 
|TAP100 = [[File:Networking_rutos_manual_wireless_interface_configuration_edit_button_tap100_v3.png|border|class=tlt-border]]
−
|RUT241|RUT200|RUT951|RUT956|RUT906 = [[File:Networking rutos manual wireless interface configuration edit button mixed v2.png|border|class=tlt-border]]
+
|RUT241|RUT200|RUT951|RUT956|RUT906|RUT901 = [[File:Networking rutos manual wireless interface configuration edit button mixed v2.png|border|class=tlt-border]]
 
}}
 
}}
 
=====General Setup=====
 
=====General Setup=====
Line 527: Line 526:  
----
 
----
 
{{#switch:{{{series}}}
 
{{#switch:{{{series}}}
−
|TAP100 = [[File:Networking rutos manual wireless interface configuration advanced settings tap100 access_point.png|border|class=tlt-border]]
+
|TAP100 = [[File:Networking rutos manual wireless interface configuration advanced settings tap100.png|border|class=tlt-border]]
 
|#default = [[File:Networking rutos manual wireless interface configuration advanced settings access_point.png|border|class=tlt-border]]}}
 
|#default = [[File:Networking rutos manual wireless interface configuration advanced settings access_point.png|border|class=tlt-border]]}}
   Line 805: Line 804:  
To begin configuring WiFi Client first click the 'Scan' button to scan the surrounding area and attempt to connect to a new wireless access point.
 
To begin configuring WiFi Client first click the 'Scan' button to scan the surrounding area and attempt to connect to a new wireless access point.
   −
{{#switch:{{{name}}}
+
[[File:Networking_rutos_manual_wireless_scan_button.png|border|class=tlt-border]]
−
|RUT241|RUT200|RUT951|RUT956|RUT906 = [[File:Networking rutos manual wireless scan button mixed wifi 2 v2.png|border|class=tlt-border]]
  −
|#default = [[File:Networking_rutos_manual_wireless_scan_button_wifi_{{{wifi}}}_{{#ifeq:{{{series}}}|TCR1|tcr1_|}}v3.png|border|class=tlt-border]]
  −
}}
      
After which you will be redirected to the window shown below, where you will see list of available WiFi Access Points in the area. Choose one according to your liking and press the '''Join Network''' button next to it.
 
After which you will be redirected to the window shown below, where you will see list of available WiFi Access Points in the area. Choose one according to your liking and press the '''Join Network''' button next to it.
   −
[[File:Networking_rutos_manual_wireless_scan_button_results_v1.png|border|class=tlt-border]]
+
[[File:Networking_rutos_manual_wireless_scan_button_results_v2.png|border|class=tlt-border]]
   −
You again will be redirected to following window, where you will need to enter WPA passphrase or other security password depending on AP that you are connecting to, name yours network (it will be name of your wireless WAN interface) and assign firewall rule.
+
You again will be redirected to following window, where you will need to enter WPA passphrase.
    
[[File:Networking_rutos_manual_wireless_scan_button_results_join_network_v2.png|border|class=tlt-border]]  
 
[[File:Networking_rutos_manual_wireless_scan_button_results_join_network_v2.png|border|class=tlt-border]]  
   −
Next window that opens will be '''Device Configuration'''. Values there, mostly, should be left unchanged to avoid connection problems, because they are dictated by Access Point. Other than that, only difference from Access Point settings are in ''Interface Configuration → General Setup'' section, where '''Mode''' is set to '''Client''', and '''Network''' attached to this wireless interface is '''WAN''' instead of LAN
+
Next window that opens will be '''Device Configuration'''. Values there, mostly, should be left unchanged to avoid connection problems, because they are dictated by Access Point. Other than that, only difference from Access Point settings are in ''Interface Configuration → General Setup'' section, where '''Mode''' is set to '''Client''', and '''Network''' attached to this wireless interface is '''wifi1''' instead of LAN
   −
[[File:Networking_rutos_manual_wireless_scan_button_results_join_network_general_setup_v2.png|border|class=tlt-border]]
+
[[File:Networking_rutos_manual_wireless_scan_button_results_join_network_general_setup_v3.png|border|class=tlt-border]]
    
Click '''Save & Apply''' and if you configured correctly, you will have Wireless Client working.
 
Click '''Save & Apply''' and if you configured correctly, you will have Wireless Client working.
Line 838: Line 834:  
To begin click the 'Add' button below of wireless interface in the Network → Wireless page:
 
To begin click the 'Add' button below of wireless interface in the Network → Wireless page:
   −
{{#switch:{{{name}}}
+
[[File:Networking rutos manual wireless mesh gateway add button v4.png|border|class=tlt-border]]
−
|RUT241|RUT200|RUT951|RUT956|RUT906 = [[File:Networking rutos manual wireless mesh gateway add button mixed v2.png|border|class=tlt-border]]
  −
|#default = [[File:Networking rutos manual wireless mesh gateway add button v3.png|border|class=tlt-border]]
  −
}}
  −
 
      
In '''General Setup''' tab change '''Mode''' to '''Mesh''', set '''Mesh ID''' (this number has to be the same in all nodes that connect to this wireless mesh network) and select desired '''Network''' which will be attached to the interface. Click '''Save & Apply'''.
 
In '''General Setup''' tab change '''Mode''' to '''Mesh''', set '''Mesh ID''' (this number has to be the same in all nodes that connect to this wireless mesh network) and select desired '''Network''' which will be attached to the interface. Click '''Save & Apply'''.
Line 876: Line 868:  
====Multi AP====
 
====Multi AP====
   −
The <b>Multi AP</b> feature is used to configure access to multiple wireless access points from one page. To enter Multi AP configuration, click the 'Multi AP' button below other Wireless configurations:
+
The <b>Multi AP</b> feature is used to configure access to multiple wireless access points from one page. To create Multi AP wireless interface click the 'Add' button below of wireless interface in the Network → Wireless page:
−
 
  −
[[File:Networking_rutos_manual_wireless_multi_ap_button_{{#ifeq:{{{series}}}|TCR1|tcr1_|}}v1.png|border|class=tlt-border]]
  −
 
  −
Next, enter a name for the Multi AP network and assign a firewall zone (default: wan).
  −
 
  −
[[File:Networking_rutos_manual_wireless_multi_ap_create_network.png|border|class=tlt-border]]
  −
 
  −
You may then start to configure General Settings for the Multi AP feature.
     −
=====General Settings=====
+
[[File:Networking rutos manual wireless mesh gateway add button v4.png|border|class=tlt-border]]
−
----
  −
The <b>General Settings</b> section for Multi AP is used to turn it on or off and to change the frequency of scanning for WiFi APs.
     −
[[File:Networking_rutos_manual_wireless_multi_ap_general_settings.png|border|class=tlt-border]]
+
In General Setup tab change Mode to Multi AP, select desired Network which will be attached to the interface. You can also select scan time and upload file with Access Points list.
   −
<table class="nd-mantable">
+
[[File:Networking_rutos_manual_wireless_multi_ap_create_network_v2.png|border|class=tlt-border]]
−
    <tr>
  −
        <th>Field</th>
  −
      <th>Value</th>
  −
      <th>Description</th>
  −
    </tr>
  −
    <tr>
  −
      <td>Enable</td>
  −
      <td>off {{!}} on; default: <b>off</b></td>
  −
      <td>Turns Multi AP configuration on or off.</td>
  −
    </tr>
  −
    <tr>
  −
      <td>Scan Time (sec)</td>
  −
      <td>integer (30+); default: <b>60</b></td>
  −
      <td>Frequency (in seconds) of scans for WiFi access point availability.</td>
  −
    </tr>
  −
    <tr>
  −
    <td>Upload AP list</td>
  −
        <td>- (interactive button)</td>
  −
        <td>Uploads a list of access point configurations.</td>
  −
    </tr>
  −
</table>
      
=====Access Points=====
 
=====Access Points=====
Retrieved from "https://wiki.teltonika-networks.com/view/Special:MobileDiff/111740"

Navigation menu