Changes

}}

}}

{{#ifeq: {{{series}}} | RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}}

{{#ifeq: {{{series}}}| RUT9 |<i><b>Note</b>: <b>[[{{{name}}} RS232/RS485 (legacy WebUI)#RS232|click here]]</b> for the old style WebUI (FW version {{Template: Networking_device_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}}

==Summary==

==Summary==

     <tr>

     <tr>

         <td>Device</td>

         <td>Device</td>

         <td>{{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}; default: <b>{{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}</b></td>

         <td>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_serial_ports | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}; default: <b>{{#ifeq:{{{default}}}|mbus|MBUS| {{Template: Networking_rutos_manual_default_serial_port | rs232={{{rs232}}} | rs485={{{rs485}}} | usb={{{usb}}} }}}}</b></td>

         <td>Specifies which serial port will be used for serial communication.</td>

         <td>Specifies which serial port will be used for serial communication.</td>

     </tr>

     </tr>

     <tr>

     <tr>

       <td>Stop bits</td>

       <td>Stop bits</td>

       <td>1 {{!}} 2; default: <b>1</b></td>

       <td>{{#switch: {{{name}}} | TRB143 = 1; default: <b>1</b>  | #default = 1 {{!}} 2; default: <b>1</b> }}</td>

       <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td>

       <td>Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.</td>

     </tr>

     </tr>

     <tr>

     <tr>

     <td>Parity</td>

     <td>Parity</td>

         <td>None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b></td>

         <td>{{#switch: {{{name}}} | TRB143 = Even {{!}} default: Even | #default = None {{!}} Odd {{!}} Even {{!}} Mark {{!}} Space; default: <b>None</b> }}</td>

         <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check.

         <td>In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check.

             <ul>

             <ul>

You can configure network related parameters of the serial connection in the <b>Over IP Configuration</b> secion.

You can configure network related parameters of the serial connection in the <b>Over IP Configuration</b> secion.

[[File:Networking rutos manual serial utilities over ip mbus configuration general_v1.png|border|class=tlt-border]]

[[File:Networking rutos manual serial utilities over ip mbus configuration general_v2.png|border|class=tlt-border]]

<table class="nd-mantable">

<table class="nd-mantable">