Line 37: |
Line 37: |
| <li><b>Factory reset</b>. If the reset button is pressed for at least 12 seconds (by default), the device will perform a factory reset and reboot. {{#ifeq:{{{sms}}}|1|{{#switch:{{{series}}}|TAP100=|#default=Signal strength LEDs indicate the elapsed time while holding the reset button. Start of the factory reset will be indicated by flashing of all {{#switch:{{{series}}}|TRB2xx|TRB5|TCR1|RUT36X|TRB2M|TRB16|TRB1|TRB2|=3|RUTX|RUTM|RUTC={{#switch:{{{name}}}|RUTX12|RUTX14|RUTXR1|RUTX50|RUTM12|RUTM50|RUTC50=3|#default=5}}|#default=5}} signal strength LEDs.}}|}} <br><b>NOTE</b>: the default button hold time value (min time 12 seconds, max time 20 seconds) can be changed in the {{#switch: {{{series}}} | | <li><b>Factory reset</b>. If the reset button is pressed for at least 12 seconds (by default), the device will perform a factory reset and reboot. {{#ifeq:{{{sms}}}|1|{{#switch:{{{series}}}|TAP100=|#default=Signal strength LEDs indicate the elapsed time while holding the reset button. Start of the factory reset will be indicated by flashing of all {{#switch:{{{series}}}|TRB2xx|TRB5|TCR1|RUT36X|TRB2M|TRB16|TRB1|TRB2|=3|RUTX|RUTM|RUTC={{#switch:{{{name}}}|RUTX12|RUTX14|RUTXR1|RUTX50|RUTM12|RUTM50|RUTC50=3|#default=5}}|#default=5}} signal strength LEDs.}}|}} <br><b>NOTE</b>: the default button hold time value (min time 12 seconds, max time 20 seconds) can be changed in the {{#switch: {{{series}}} |
| | TRB14x|TRB2xx|TRB5|TRB16|TRB2M|TRB1|TRB2 = gateway | | | TRB14x|TRB2xx|TRB5|TRB16|TRB2M|TRB1|TRB2 = gateway |
− | | router's}} WebUI, from the <b>System → Administration → [[{{{name}}}_Administration#General|General]]</b> page.</li> | + | | TAP100|TAP200 = AP's |
| + | | #default = router's}} WebUI, from the <b>System → Administration → [[{{{name}}}_Administration#General|General]]</b> page.</li> |
| </ul> | | </ul> |
| | | |
Line 47: |
Line 48: |
| [[File:Networking_rutos_manual_device_recovery_option_reset_webui.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_device_recovery_option_reset_webui.png|border|class=tlt-border]] |
| | | |
− | | #default=You can also perform a factory reset from the router's WebUI. To do so, login to the router and go to the Backup section found under the System tab (<b>System → Maintenance → Backup → [[{{{name}}}_Maintenance#Restore_default_settings|Reset settings]]</b>). In the very bottom of the page there's a <b>Reset</b> button that performs a chosen type of reset.}} | + | | #default=You can also perform a factory reset from the {{#switch: {{{series}}}|TRB14x|TRB2xx|TRB5|TRB16|TRB2M|TRB1|TRB2 = gateway's | TAP100|TAP200 = AP's | #default = router's}} WebUI. To do so, login to the {{#switch: {{{series}}}|TRB14x|TRB2xx|TRB5|TRB16|TRB2M|TRB1|TRB2 = gateway's | TAP100|TAP200 = AP's | #default = router's}} and go to the Backup section found under the System tab (<b>System → Maintenance → Backup → [[{{{name}}}_Maintenance#Restore_default_settings|Reset settings]]</b>). In the very bottom of the page there's a <b>Reset</b> button that performs a chosen type of reset.}} |
| | | |
| Notice: A <b>Factory defaults</b> reset will remove all logs, SIM PIN's and RMS data that the device might have had. | | Notice: A <b>Factory defaults</b> reset will remove all logs, SIM PIN's and RMS data that the device might have had. |
Line 65: |
Line 66: |
| You can perform a factory reset via command line by executing the <b>firstboot</b> command. After this you will be asked to confirm the reset. If you're sure, type the letter <b>y</b> and press "Enter" or type the letter <b>n</b> if you wish to cancel the reset. | | You can perform a factory reset via command line by executing the <b>firstboot</b> command. After this you will be asked to confirm the reset. If you're sure, type the letter <b>y</b> and press "Enter" or type the letter <b>n</b> if you wish to cancel the reset. |
| | | |
− | If you agreed to perform a factory reset, next type in <b>reboot</b> and press "Enter". The {{#switch: {{{series}}} |TRB1xx|TRB2xx|TRB5|TRB1|TRB2|TRB2M|TRB16=gateway|#default=router}} will be reset to it's factory settings and rebooted. The entire sequence of events should look like this: | + | If you agreed to perform a factory reset, next type in <b>reboot</b> and press "Enter". The {{#switch: {{{series}}}|TRB14x|TRB2xx|TRB5|TRB16|TRB2M|TRB1|TRB2 = gateway | TAP100|TAP200 = AP | #default = router}} will be reset to it's factory settings and rebooted. The entire sequence of events should look like this: |
| | | |
| {{Template: Networking_{{#ifeq:{{{series}}}|TRB14x|{{lc:{{{series}}}}}|rutxxx}}_manual_device_recovery_cli | | {{Template: Networking_{{#ifeq:{{{series}}}|TRB14x|{{lc:{{{series}}}}}|rutxxx}}_manual_device_recovery_cli |