Line 23: |
Line 23: |
| ==Configuration of VXLAN over Wired WAN== | | ==Configuration of VXLAN over Wired WAN== |
| In this section, the setup of VXLAN over Wired WAN using RUT1 and RUT2 devices will be described. The process will show how to create a VXLAN tunnel to connect the devices and allow them to communicate over the wired network. | | In this section, the setup of VXLAN over Wired WAN using RUT1 and RUT2 devices will be described. The process will show how to create a VXLAN tunnel to connect the devices and allow them to communicate over the wired network. |
− | ===Configuring the Wired WAN Interfaces=== | + | ===RUT1 Configuration=== |
| ---- | | ---- |
− | The same steps will be followed to configure the WAN interfaces on RUT1 and RUT2, which will be on the same subnet but with different IP addresses, enabling layer 3 communication between them.
| |
− |
| |
| ====RUT1 WAN configuration==== | | ====RUT1 WAN configuration==== |
| | | |
Line 40: |
Line 38: |
| [[File:Vxlan_over_wired_wan_settings_rut1.png|border|class=tlt-border]] | | [[File:Vxlan_over_wired_wan_settings_rut1.png|border|class=tlt-border]] |
| | | |
− | ====RUT2 WAN configuration==== | + | ====RUT1 VXLAN configuration==== |
| + | |
| + | Navigate to the '''Network > WAN''' |
| + | #In '''Add new device''' section select Type '''VXLAN''' |
| + | #Press [[File:Add Button.png|50px]] |
| + | [[File:Vxlan over wired vxlan settings add.png|border|class=tlt-border]] |
| + | #<li value="3">Enter name of the new VXLAN interface |
| + | # Enter the Remote address corresponding to RUT2 wired WAN interface IP address |
| + | # Click [[File:Save & Apply.png|90px]] twice |
| + | [[File:Vxlan over wired vxlan settings rut1.png|border|class=tlt-border]] |
| + | |
| + | ====RUTX LAN configuration==== |
| + | |
| + | [[File:Vxlan over wired lan config.png|border|class=tlt-border]] |
| + | [[File:Vxlan over wired lan physical settings.png|border|class=tlt-border]] |
| + | |
| + | |
| + | |
| + | ==RUT2 WAN configuration== |
| | | |
| Navigate to the '''Network > WAN''' section in the WebUI, then click the '''Edit''' button for the wired WAN interface. | | Navigate to the '''Network > WAN''' section in the WebUI, then click the '''Edit''' button for the wired WAN interface. |
Line 57: |
Line 73: |
| The same steps will be followed to configure the WAN interfaces on RUT1 and RUT2, which will be on the same subnet but with different IP addresses, enabling layer 3 communication between them | | The same steps will be followed to configure the WAN interfaces on RUT1 and RUT2, which will be on the same subnet but with different IP addresses, enabling layer 3 communication between them |
| | | |
− | ====RUT1 VXLAN configuration====
| |
− |
| |
− | Navigate to the '''Network > WAN'''
| |
− | #In '''Add new device''' section select Type '''VXLAN'''
| |
− | #Press [[File:Add Button.png|50px]]
| |
− | [[File:Vxlan over wired vxlan settings add.png|border|class=tlt-border]]
| |
− | #<li value="3">Enter name of the new VXLAN interface
| |
− | # Enter the Remote address corresponding to RUT2 wired WAN interface IP address
| |
− | # Click [[File:Save & Apply.png|90px]] twice
| |
− | [[File:Vxlan over wired vxlan settings rut1.png|border|class=tlt-border]]
| |
| | | |
| ====RUT2 VXLAN configuration==== | | ====RUT2 VXLAN configuration==== |
Line 80: |
Line 86: |
| | | |
| | | |
− |
| |
− | ===Configuring LAN interfaces===
| |
− | ----
| |
− | The same steps will be followed to configure the WAN interfaces on RUT1 and RUT2, which will be on the same subnet but with different IP addresses, enabling layer 3 communication between them
| |
− | [[File:Vxlan over wired lan config.png|border|class=tlt-border]]
| |
− | [[File:Vxlan over wired lan physical settings.png|border|class=tlt-border]]
| |
| [[File:Vxlan over wired lan config rut2.png|border|class=tlt-border]] | | [[File:Vxlan over wired lan config rut2.png|border|class=tlt-border]] |
| [[File:Vxlan over wired lan settings RUT2.png|border|class=tlt-border]] | | [[File:Vxlan over wired lan settings RUT2.png|border|class=tlt-border]] |
| | | |
| ==Configuring VXLAN over 2 Public IP addresses== | | ==Configuring VXLAN over 2 Public IP addresses== |
| + | The same steps will be followed to configure the WAN interfaces on RUT1 and RUT2, which will be on the same subnet but with different IP addresses, enabling layer 3 communication between them. |