Changes

RUT955 Routing (view source)

Revision as of 08:56, 1 March 2019

109 bytes removed , 08:56, 1 March 2019

no edit summary

Line 18: Line 18:

<tr>

<td>Routing table</td>

−

<td>Main ~~{{!}}~~ WAN ~~{{!}}~~ WAN2 ~~{{!}}~~ WAN3; Default: '''WAN'''</td>

+

<td>Main | WAN | WAN2 | WAN3; Default: '''WAN'''</td>

<td>Defines which table will be used for the route in question</td>

</tr>

<tr>

<td>Interface</td>

−

<td>LAN ~~{{!}}~~ WAN(wired) ~~{{!}}~~ WAN2(Mobile) ~~{{!}}~~ WAN3(WiFi) ~~{{!}}~~ VPN instances; Default: '''WAN(wired)'''</td>

+

<td>LAN | WAN(wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: '''WAN(wired)'''</td>

<td>The zone where the target network resides</td>

</tr>

Line 111: Line 111:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles the BGP protocol ON or OFF</td>

</tr>

<tr>

<td>Enable vty</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles vty access from LAN ON or OFF</td>

</tr>

Line 139: Line 139:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles the BGP instance ON or OFF</td>

</tr>

Line 172: Line 172:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles the BGP peer ON or OFF</td>

</tr>

Line 200: Line 200:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles the Access filter ON or OFF</td>

</tr>

Line 210: Line 210:

<tr>

<td>Action</td>

−

<td>Permit ~~{{!}}~~ Deny; Default: '''Permit'''</td>

+

<td>Permit | Deny; Default: '''Permit'''</td>

<td>Denies or permits matched entry</td>

</tr>

<tr>

<td>Network</td>

−

<td>Any ~~{{!}}~~ ip; Default: '''Any'''</td>

+

<td>Any | ip; Default: '''Any'''</td>

<td>Applies filter rule for this source network</td>

</tr>

<tr>

<td>Direction</td>

−

<td>Inbound ~~{{!}}~~ Outbound; Default: '''Inbound'''</td>

+

<td>Inbound | Outbound; Default: '''Inbound'''</td>

<td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td>

</tr>

Line 242: Line 242:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles RIP Protocol ON or OFF</td>

</tr>

<tr>

<td>Enable vty</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles vty access from LAN ON or OFF</td>

</tr>

Line 257: Line 257:

<tr>

<td>Version</td>

−

<td>2 ~~{{!}}~~ 1; Default: '''2'''</td>

+

<td>2 | 1; Default: '''2'''</td>

<td>Specifies the version of RIP</td>

</tr>

Line 280: Line 280:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles RIP Interface ON or OFF</td>

</tr>

Line 290: Line 290:

<tr>

<td>Passive interface</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Sets the specified interface to passive mode. On passive mode interface, all receiving packets are processed as normal and ripd does not send either multicast or unicast RIP packets</td>

</tr>

Line 308: Line 308:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles the Access filter ON or OFF</td>

</tr>

Line 318: Line 318:

<tr>

<td>Action</td>

−

<td>Permit ~~{{!}}~~ Deny; Default: '''Permit'''</td>

+

<td>Permit | Deny; Default: '''Permit'''</td>

<td>Denies or permits matched entry</td>

</tr>

<tr>

<td>Network</td>

−

<td>Any ~~{{!}}~~ ip; Default: '''Any'''</td>

+

<td>Any | ip; Default: '''Any'''</td>

<td>Applies filter rule for this source network</td>

</tr>

<tr>

<td>Direction</td>

−

<td>Inbound ~~{{!}}~~ Outbound; Default: '''Inbound'''</td>

+

<td>Inbound | Outbound; Default: '''Inbound'''</td>

<td>If direction is '''Inbound''', the access list is applied to input routes. If direction is '''Outbound''' the access list is applied to advertised routes</td>

</tr>

Line 349: Line 349:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles OSPF Protocol ON or OFF</td>

</tr>

<tr>

<td>Enable vty</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles vty access from LAN ON or OFF</td>

</tr>

Line 381: Line 381:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles OSPF interface ON or OFF</td>

</tr>

Line 411: Line 411:

<tr>

−

<td>Broadcast ~~{{!}}~~ Nonbroadcast ~~{{!}}~~ Point-to-point ~~{{!}}~~ Point-to-multipoint; Default: " "</td>

+

<td>Broadcast | Nonbroadcast | Point-to-point | Point-to-multipoint; Default: " "</td>

<td>Set explicit network type for the specified interface</td>

</tr>

<tr>

<td>Authentication</td>

−

<td>None ~~{{!}}~~ Password ~~{{!}}~~ MD5 HMAC; Default: " "</td>

+

<td>None | Password | MD5 HMAC; Default: " "</td>

<td>Specifies the authentication mode that should be used for the interface</td>

</tr>

Line 434: Line 434:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles OSPF area ON or OFF</td>

</tr>

Line 457: Line 457:

<tr>

<td>Enable</td>

−

<td>yes ~~{{!}}~~ no; Default: '''no'''</td>

+

<td>yes | no; Default: '''no'''</td>

<td>Toggles OSPF network ON or OFF</td>

</tr>

Line 471: Line 471:

</tr>

</table>

+

[[Category:RUT955 WebUI]]

Dziugas

Bureaucrats, Interface administrators, Administrators

31,703

edits