31,703
edits
Changes
Template:Networking rut manual setup wizard (view source)
Revision as of 15:43, 12 July 2019
, 15:43, 12 July 2019no edit summary
==Set new password==
==Set new password==
On your very first login you will be <b>required to change the router's default password</b>. This is done for safety reasons. In many cases routers are used to provide access to remote networks and systems. Since many manufacturers use similar default passwords (like <i>admin</i>, <i>admin01</i>, <i>admin123</i>, etc.) it is easy for attackers to gain access to routers that use such passwords and compromise the systems behind the router. Therefore, to avoid such malicious attacks, this step is mandatory and you will not able to access the rest of the WebUI before you change the password.
On your very first login you will be <b>required to change the router's default password</b>. This is done for safety reasons. In many cases routers are used to provide access to remote networks and systems. Since many manufacturers use similar default passwords (like <i>admin</i>, <i>admin01</i>, <i>admin123</i>, etc.) it is easy for attackers to gain access to routers that use such passwords and compromise the systems behind them. Therefore, to avoid such malicious attacks, this step is mandatory and you will not able to access the rest of the WebUI before you change the password.
The new password must contain:
The new password must contain:
[[File:{{{file_password}}}]]
[[File:{{{file_password}}}]]
After you have entered the new password, click 'Submit'. Afterwards you will be redirected to the first page of the Setup Wizard.
After you have entered the new password, click 'Save'. Afterwards you will be redirected to the first page of the Setup Wizard.
==General==
==General==
If you wish to set the router's time zone settings later instead, you can do so via the <i>Services → [[{{{name}}} NTP|NTP]]</i> page.
If you wish to set the router's time zone settings later instead, you can do so via the <i>Services → [[{{{name}}} NTP|NTP]]</i> page.
==Mobile==
The <b>Mobile</b> section is used to configure the router's SIM card parameters.
[[File:{{{file_wan}}}]]
<table class="nd-mantable">
<tr>
<th>Field</th>
<th>Value</th>
<th>Description</th>
</tr>
<tr>
<td>APN</td>
<td>string; default: <b>none</b></td>
<td>An Access Point Name (APN) is a gateway between a GSM, GPRS, 3G or 4G mobile network and another computer network. Depending on the contract, some operators may require you to enter the APN just to complete the registration to a network. In other cases an APN is used to get special parameters from the operator (e.g., a [[Private_and_Public_IP_Addresses#Public_IP_address|public IP address]]) depending on the contract.<br><b>Important note</b>: an APN Network Identifier cannot start with any of the following strings: "rac", "lac", "sgsn" or "rnc"; it cannot end in ".gprs" and it cannot take the value "*".</td>
</tr>
<tr>
<td>PIN number</td>
<td>string; default: <b>none</b></td>
<td>A 4-digit long numeric password used to authenticate the modem to the SIM card.</td>
</tr>
<tr>
<td>Dialing number</td>
<td>string; default: <b>none</b></td>
<td>A dialing number required to establish a mobile PPP connection.</td>
</tr>
<tr>
<td>MTU</td>
<td>string; default: <b>none</b></td>
<td>Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.</td>
</tr>
<tr>
<td>Authentication method</td>
<td>CHAP | PAP | None; default: <b>None</b></td>
<td>The method that your carrier uses to authenticate new connections on its network. If you select PAP or CHAP you will be required to enter a username and password.</td>
</tr>
<tr>
<td>Service mode</td>
<td>2G only | 3G only | {{#ifeq:{{{3g}}}|1||4G (LTE) only | }}}Automatic; default: <b>Automatic</b></td>
<td>Preffered service type.</td>
</tr>
<tr>
<td>Show mobile info at login page</td>
<td>yes | no; default: <b>no</b></td>
<td>When this field is checked, information about the router's mobile connection will be displayed in the login page.</td>
</tr>
</table>
If you wish to set the router's Mobile settings later instead, you can do so via the <i>Network → [[{{{name}}} Mobile|Mobile]]</i> page.
==LAN==
==LAN==
