31,703
edits
Changes
Blocking Internet Access for LAN Clients (view source)
Revision as of 10:36, 10 July 2020
, 10:36, 10 July 2020Created page with "==Introduction== This article contains instructions o how to block Internet access for LAN clients using a Teltonika-Networks device. ==Blocking WAN (Internet) access== Acc..."
==Introduction==
This article contains instructions o how to block Internet access for LAN clients using a Teltonika-Networks device.
==Blocking WAN (Internet) access==
Access between your end device and other networks is controlled by your network device's (router, gateway) firewall. Therefore, in order to set networks access limitations you will need to modify the firewall configuration. In the Teltonika-Networks devices this can be done over the <b>Network → Firewall</b> page.
To access the Firewall page, you must first switch to 'Advanced' WebUI mode:
[[File:Networking_rutx_manual_webui_basic_advanced_mode_v1.gif|border|class=tlt-border]]
===All clients===
----
<ul>
<li>Go to the <b>Network → Firewall → Traffic Rules</b> page.</li>
<li>Scroll down to the 'Add New Forward Rule' section and create a rule such as this:
<ol>
<li>Create a custom name for the rule.</li>
<li>Set 'Source Zone' to <i>lan</i>.</li>
<li>Set 'Destination Zone' to <i>wan</i>.</li>
<li>Click 'Add'.</li>
</ol>[[File:Networking_device_faq_blocking_internet_access_for_lan_clients_1.png|border|class=tlt-border]]
</li>
<li>When the rule is created, you will be redirected to its configuration page. While there, set up the rule like this:
<ol>
<li>Set 'Protocol' to <i>Any</i>.</li>
<li>Set 'Action' to <i>Drop</i>.</li>
</ol>[[File:Networking_device_faq_blocking_internet_access_for_lan_clients_2.png|border|class=tlt-border]]
</li>
</ul>
===Single client===
----
==Blocking specific site or address==
[[Category:Networking]]
This article contains instructions o how to block Internet access for LAN clients using a Teltonika-Networks device.
==Blocking WAN (Internet) access==
Access between your end device and other networks is controlled by your network device's (router, gateway) firewall. Therefore, in order to set networks access limitations you will need to modify the firewall configuration. In the Teltonika-Networks devices this can be done over the <b>Network → Firewall</b> page.
To access the Firewall page, you must first switch to 'Advanced' WebUI mode:
[[File:Networking_rutx_manual_webui_basic_advanced_mode_v1.gif|border|class=tlt-border]]
===All clients===
----
<ul>
<li>Go to the <b>Network → Firewall → Traffic Rules</b> page.</li>
<li>Scroll down to the 'Add New Forward Rule' section and create a rule such as this:
<ol>
<li>Create a custom name for the rule.</li>
<li>Set 'Source Zone' to <i>lan</i>.</li>
<li>Set 'Destination Zone' to <i>wan</i>.</li>
<li>Click 'Add'.</li>
</ol>[[File:Networking_device_faq_blocking_internet_access_for_lan_clients_1.png|border|class=tlt-border]]
</li>
<li>When the rule is created, you will be redirected to its configuration page. While there, set up the rule like this:
<ol>
<li>Set 'Protocol' to <i>Any</i>.</li>
<li>Set 'Action' to <i>Drop</i>.</li>
</ol>[[File:Networking_device_faq_blocking_internet_access_for_lan_clients_2.png|border|class=tlt-border]]
</li>
</ul>
===Single client===
----
==Blocking specific site or address==
[[Category:Networking]]
