31,703
edits
Changes
Template:Networking rutos manual routing (view source)
Revision as of 08:52, 21 October 2020
, 08:52, 21 October 2020no edit summary
<td>Remote AS</td>
<td>Remote AS</td>
<td>integer [1..65535]; default: <b>none</b></td>
<td>integer [1..65535]; default: <b>none</b></td>
<td>Remote autonomous system number of this remote BGP Neighbour.</td>
<td>Remote autonomous system number of this remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Remote address</td>
<td>Remote address</td>
<td>ip4; default: <b>none</b></td>
<td>ip4; default: <b>none</b></td>
<td>IPv4 address of this remote BGP Neighbour.</td>
<td>IPv4 address of this remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Remote AS</td>
<td>Remote AS</td>
<td>integer [1..65535]; default: <b>none</b></td>
<td>integer [1..65535]; default: <b>none</b></td>
<td>Remote autonomous system number of this remote BGP Neighbour.</td>
<td>Remote autonomous system number of this remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Remote address</td>
<td>Remote address</td>
<td>ip4; default: <b>none</b></td>
<td>ip4; default: <b>none</b></td>
<td>IPv4 address of this remote BGP Neighbour.</td>
<td>IPv4 address of this remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Remote port</td>
<td>Remote port</td>
<td>integer [0..65535]; default: <b>none</b></td>
<td>integer [0..65535]; default: <b>none</b></td>
<td>Listening port number of the BGP Neighbour.</td>
<td>Listening port number of the BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>EBGP Multihop</td>
<td>EBGP Multihop</td>
<td>integer; default: <b>none</b></td>
<td>integer; default: <b>none</b></td>
<td>Time to Live value for packets associated with this remote BGP Neighbour.</td>
<td>Time to Live value for packets associated with this remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Neighbor address</td>
<td>Neighbor address</td>
<td>ip4; default: <b>none</b></td>
<td>ip4; default: <b>none</b></td>
<td>IPv4 address(es) of a remote BGP Neighbour.</td>
<td>IPv4 address(es) of a remote BGP Neighbor.</td>
</tr>
</tr>
<tr>
<tr>
<td>Neighbor configuration</td>
<td>Neighbor configuration</td>
<td>None <nowiki>|</nowiki> Route Reflector client <nowiki>|</nowiki> Route Server client; default: <b>None</b></td>
<td>None <nowiki>|</nowiki> Route Reflector client <nowiki>|</nowiki> Route Server client; default: <b>None</b></td>
<td>Defines the role of a BGP Neighbour.
<td>Defines the role of a BGP Neighbor.
<ul>
<ul>
<li><b>Route Reflector client</b> - redistributes received routes.</li>
<li><b>Route Reflector client</b> - redistributes received routes.</li>
<td>Inbound soft-reconfiguration</td>
<td>Inbound soft-reconfiguration</td>
<td>off <nowiki>|</nowiki> on; default: <b>off</b></td>
<td>off <nowiki>|</nowiki> on; default: <b>off</b></td>
<td>Turns inbound soft-reconfiguration for this neighbor on or off.</td>
<td>Turns inbound soft-reconfiguration for this Neighbor on or off.</td>
</tr>
</tr>
<tr>
<tr>
<td>Disable connected check</td>
<td>Disable connected check</td>
<td>off <nowiki>|</nowiki> on; default: <b>off</b></td>
<td>off <nowiki>|</nowiki> on; default: <b>off</b></td>
<td>When turned on, Disable connected check enables a directly connected eBGP neighbor to peer using a loopback address without adjusting the default TTL of 1.</td>
<td>When turned on, Disable connected check enables a directly connected eBGP Neighbor to peer using a loopback address without adjusting the default TTL of 1.</td>
</tr>
</tr>
</table>
</table>
<tr>
<tr>
<td>Neighbor</td>
<td>Neighbor</td>
<td>rip neighbour; default: <b>none</b></td>
<td>rip neighbor; default: <b>none</b></td>
<td>Defines a RIP Neighbour(s).</td>
<td>Defines a RIP Neighbor(s).</td>
</tr>
</tr>
</table>
</table>
====Access list filters====
====Access list filters====
----
----
The <b>Access List Filters</b> section is used to configure special filters that restrict or allow access to specified networks for RIP Neighbours. Below is an example of the Access List Filters section which is empty by default.
The <b>Access List Filters</b> section is used to configure special filters that restrict or allow access to specified networks for RIP Neighbors. Below is an example of the Access List Filters section which is empty by default.
[[File:Networking_rutos_manual_routing_dynamic_routes_rip_access_list_filters.png|border|class=tlt-border]]
[[File:Networking_rutos_manual_routing_dynamic_routes_rip_access_list_filters.png|border|class=tlt-border]]
<td>Neighbors</td>
<td>Neighbors</td>
<td>ip4; default: <b>none</b></td>
<td>ip4; default: <b>none</b></td>
<td>Defines the EIGRP Neighbours (based on their IP addresses) that this device is meant to associate with.</td>
<td>Defines the EIGRP Neighbors (based on their IP addresses) that this device is meant to associate with.</td>
</tr>
</tr>
</table>
</table>
