31,703
edits
Changes
Template:Networking rutos manual input output pinout (view source)
Revision as of 16:26, 4 November 2020
, 16:26, 4 November 2020Created page with "{{#ifeq: {{{series}}} | TRB2 | ===16 pin Connector Pinout=== ---- border|class=tlt-border <ul>..."
{{#ifeq: {{{series}}} | TRB2 |
===16 pin Connector Pinout===
----
[[File:Networking_trb2_manual_input_output_input_output_connector_pinout.png|border|class=tlt-border]]
<ul>
<li><b>+</b>: {{{input_volts}}} VDC positive (+).</li>
<li><b>D1</b>, <b>D2</b>, <b>D3</b> - programmable input/output pins; can be set to:
<ul>
<li><i>open collector (OC) output;</i> max 30 V, 300 mA;</li>
<li><i>digital input;</i> 0-6 V is detected as logic "low"; 8-30 V is detected as logic "high".</li>
</ul>
</li>
<li><b>CTS</b> - RS232 clear data to send (output).</li>
<li><b>RTS</b> - RS232 request data to send (input).</li>
<li><b>R+</b> - RS485 receiver positive signal.</li>
<li><b>D+</b> - RS485 driver positive signal.</li>
<li><b>-</b> - negative/ground (-).</li>
<li><b>⏚</b> - GND pins for D1, D2, D3, A, RS232 and RS485</li>
<li><b>A</b> - Analog input. Voltage range: 0-30 V.</li>
<li><b>TX</b> - RS232 transmitted data (input).</li>
<li><b>RX</b> - RS232 received data (output).</li>
<li><b>R-</b> - RS485 receiver negative signal.</li>
<li><b>D-</b> - RS485 driver negative signal.</li>
</ul>|
===Power Socket Pinout===
----
[[File:Networking_rutos_manual_input_output_power_socket_pinout_configurableio_{{{configurableio}}}.png]]
<ul>
<li><b>Power</b>: {{{input_volts}}} VDC positive (+).</li>
<li><b>Ground</b>: negative/ground (-).</li>{{#ifeq: {{{configurableio}}} | 1 |
<li><b>I/O</b>: programmable input/output pins; can be set to:
<ul>
<li><i>open collector (OC) output;</i> max 30 V;</li>
<li><i>digital input;</i> 0-7.3 V is detected as logical "0"; 7.3-30 V is detected as logical "1".</li>
</ul>
</li>|
<li><b>Input</b>: digital non-isolated input.
<ul>
<li><i>logical low level:</i> 0 - 5 V;</li>
<li><i>logical high level:</i> 8 - 40 V.</li>
</ul>
</li>
<li><b>Output</b>: digital open collector (OC) output; 30 V, 300 mA.</li>}}
</ul>}}
===16 pin Connector Pinout===
----
[[File:Networking_trb2_manual_input_output_input_output_connector_pinout.png|border|class=tlt-border]]
<ul>
<li><b>+</b>: {{{input_volts}}} VDC positive (+).</li>
<li><b>D1</b>, <b>D2</b>, <b>D3</b> - programmable input/output pins; can be set to:
<ul>
<li><i>open collector (OC) output;</i> max 30 V, 300 mA;</li>
<li><i>digital input;</i> 0-6 V is detected as logic "low"; 8-30 V is detected as logic "high".</li>
</ul>
</li>
<li><b>CTS</b> - RS232 clear data to send (output).</li>
<li><b>RTS</b> - RS232 request data to send (input).</li>
<li><b>R+</b> - RS485 receiver positive signal.</li>
<li><b>D+</b> - RS485 driver positive signal.</li>
<li><b>-</b> - negative/ground (-).</li>
<li><b>⏚</b> - GND pins for D1, D2, D3, A, RS232 and RS485</li>
<li><b>A</b> - Analog input. Voltage range: 0-30 V.</li>
<li><b>TX</b> - RS232 transmitted data (input).</li>
<li><b>RX</b> - RS232 received data (output).</li>
<li><b>R-</b> - RS485 receiver negative signal.</li>
<li><b>D-</b> - RS485 driver negative signal.</li>
</ul>|
===Power Socket Pinout===
----
[[File:Networking_rutos_manual_input_output_power_socket_pinout_configurableio_{{{configurableio}}}.png]]
<ul>
<li><b>Power</b>: {{{input_volts}}} VDC positive (+).</li>
<li><b>Ground</b>: negative/ground (-).</li>{{#ifeq: {{{configurableio}}} | 1 |
<li><b>I/O</b>: programmable input/output pins; can be set to:
<ul>
<li><i>open collector (OC) output;</i> max 30 V;</li>
<li><i>digital input;</i> 0-7.3 V is detected as logical "0"; 7.3-30 V is detected as logical "1".</li>
</ul>
</li>|
<li><b>Input</b>: digital non-isolated input.
<ul>
<li><i>logical low level:</i> 0 - 5 V;</li>
<li><i>logical high level:</i> 8 - 40 V.</li>
</ul>
</li>
<li><b>Output</b>: digital open collector (OC) output; 30 V, 300 mA.</li>}}
</ul>}}
