Line 1: |
Line 1: |
| {{Template:Networking_rutos_manual_fw_disclosure | | {{Template:Networking_rutos_manual_fw_disclosure |
− | | fw_version = {{{series}}}_R_00.02.05.1 | + | | fw_version = {{{series}}}_R_00.02.06.1 |
| | series = {{{series}}} | | | series = {{{series}}} |
| }} | | }} |
Line 34: |
Line 34: |
| <li><b>NC<sub>1</sub></b>, <b>C<sub>1</sub></b> & <b>NO<sub>1</sub></b> - Normally Closed, Common and Normally Open contacts of the internal Non-Latching Relay respectively.<br>Maximum relay ratings: 0.5 A at 60 VDC/70 VAC, 1 A at 30 VDC/VAC.</li> | | <li><b>NC<sub>1</sub></b>, <b>C<sub>1</sub></b> & <b>NO<sub>1</sub></b> - Normally Closed, Common and Normally Open contacts of the internal Non-Latching Relay respectively.<br>Maximum relay ratings: 0.5 A at 60 VDC/70 VAC, 1 A at 30 VDC/VAC.</li> |
| <li><b>NC<sub>2</sub></b>, <b>C<sub>2</sub></b> & <b>NO<sub>2</sub></b> - Normally Closed, Common and Normally Open contacts of the internal Latching Relay respectively.<br>Maximum relay ratings: 0.8 A at 70 VDC, 0.9 A at 70 VAC, 2 A at 30 VDC/VAC.</li> | | <li><b>NC<sub>2</sub></b>, <b>C<sub>2</sub></b> & <b>NO<sub>2</sub></b> - Normally Closed, Common and Normally Open contacts of the internal Latching Relay respectively.<br>Maximum relay ratings: 0.8 A at 70 VDC, 0.9 A at 70 VAC, 2 A at 30 VDC/VAC.</li> |
− | <li><b>A</b> - ADC input. Analog voltage range: 0-30 V. The input can be configured for 4-20 mA sensor protocol as current measurement of 0-30 mA.</li> | + | <li><b>A</b> - ADC input. Analog voltage range: 0-30 V. The input can be configured for 4-20 mA sensor protocol as current measurement (ACL) of 0-30 mA.</li> |
| <li><b>l</b> and <b>⏚</b> - isolated input contacts. | | <li><b>l</b> and <b>⏚</b> - isolated input contacts. |
| <ul> | | <ul> |
Line 68: |
Line 68: |
| ==Post/Get== | | ==Post/Get== |
| | | |
− | Enabling <b>Post/Get</b> provides the possibility to control the state of an output via HTTP POST/GET requests. The figure below is an example of the Auth Settings section of the Post/Get page. It is used to turn Post/Get on or off and to set authentication parameters. | + | Enabling <b>Post/Get</b> provides the possibility to control the state of an output via HTTP POST/GET requests. The figure below is an example of the Auth Settings section of the Post/Get page. It is used to turn Post/Get requests on or off and to set authentication parameters. |
| | | |
| [[File:Networking_rutos_manual_input_output_post_get_auth_settings.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_input_output_post_get_auth_settings.png|border|class=tlt-border]] |
Line 102: |
Line 102: |
| ===Post/Get examples=== | | ===Post/Get examples=== |
| ---- | | ---- |
− | It is possible to turn the output on and off by using a valid HTTP POST/GET syntax. Use a web browser or any other compatible software to submit HTTP POST/GET strings to the device.
| + | Use a web browser or any other compatible software to send HTTP POST/GET requests to the device. |
| | | |
| Below is a table containing syntax examples of this usage: | | Below is a table containing syntax examples of this usage: |
Line 172: |
Line 172: |
| After this you should be redirected to the configuration page for the newly added Instance which should look similar to this: | | After this you should be redirected to the configuration page for the newly added Instance which should look similar to this: |
| | | |
− | [[File:Networking_rutos_manual_input_output_scheduler_instance_configuration_{{{configurableio}}}.png|border|class=tlt-border]] | + | [[File:Networking_rutos_manual_input_output_scheduler_instance_configuration_configurableio_{{{configurableio}}}.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 453: |
Line 453: |
| ====HTTP==== | | ====HTTP==== |
| ---- | | ---- |
− | Executes at HTTP Post/Get action. | + | Executes a HTTP POST/GET request. |
| | | |
| [[File:Networking_rutos_manual_input_output_io_juggler_actions_http.png|border|class=tlt-border]] | | [[File:Networking_rutos_manual_input_output_io_juggler_actions_http.png|border|class=tlt-border]] |