378
edits
Changes
Template:Networking rut9m manual input output status (view source)
Revision as of 09:37, 13 January 2022
, 09:37, 13 January 2022Created page with "{{#ifeq:{{{name}}}|RUT956| <pre> ioman.gpio.din1 - 4PIN input ioman.gpio.dout1 - 4PIN output ioman.gpio.din2 - Digital input (only for passive sensors) ioman.gpio.dout..."
{{#ifeq:{{{name}}}|RUT956|
<pre>
ioman.gpio.din1 - 4PIN input
ioman.gpio.dout1 - 4PIN output
ioman.gpio.din2 - Digital input (only for passive sensors)
ioman.gpio.dout2 - Galvanically isolated open collector output
ioman.relay.relay0 - Digital relay output
ioman.gpio.iio - Digital galvanically isolated input
ioman.adc.adc0 - Analog input
ioman.acl.acl0 - Analog Current loop
</pre>|
<pre>
ioman.gpio.din1 - 4PIN input
ioman.gpio.dout1 - 4PIN output
</pre>
}}
Call command <b>ubus call <u>value</u> status </b>:
root@Teltonika-{{{name}}}:~# ubus call ioman.gpio.din1 status
{
"value": "0",
"direction": "in",
"bi_dir": false,
"invert_input": false
}
<ul>
<li><b>din1</b> is the input:
<ul>
<li>"value": "<b>0</b>" means low level state.</li>
<li>"value": "<b>1</b>" means high level state.</li>
</ul>
</li>
<li><b>dout1</b> is the output:
<ul>
<li>"value": "<b>0</b>" means low level state.</li>
<li>"value": "<b>1</b>" means high level state.</li>
</ul>
</li>{{#ifeq:{{{name}}}|RUT956|
<li><b>relay0</b> is the relay:
<ul>
<li>"state": "<b>open</b>" means open relay state.</li>
<li>"state": "<b>closed</b>" means closed relay state.</li>
</ul>
</li>|}}
</ul>
{{#ifeq:{{{name}}}|RUT956|
To change relay settings, use the <i><b>update</i></b> command and specify a state:
ubus call ioman.relay.relay0 update '{"state":"open"}'
ubus call ioman.relay.relay0 update '{"state":"closed"}'
|}}
<pre>
ioman.gpio.din1 - 4PIN input
ioman.gpio.dout1 - 4PIN output
ioman.gpio.din2 - Digital input (only for passive sensors)
ioman.gpio.dout2 - Galvanically isolated open collector output
ioman.relay.relay0 - Digital relay output
ioman.gpio.iio - Digital galvanically isolated input
ioman.adc.adc0 - Analog input
ioman.acl.acl0 - Analog Current loop
</pre>|
<pre>
ioman.gpio.din1 - 4PIN input
ioman.gpio.dout1 - 4PIN output
</pre>
}}
Call command <b>ubus call <u>value</u> status </b>:
root@Teltonika-{{{name}}}:~# ubus call ioman.gpio.din1 status
{
"value": "0",
"direction": "in",
"bi_dir": false,
"invert_input": false
}
<ul>
<li><b>din1</b> is the input:
<ul>
<li>"value": "<b>0</b>" means low level state.</li>
<li>"value": "<b>1</b>" means high level state.</li>
</ul>
</li>
<li><b>dout1</b> is the output:
<ul>
<li>"value": "<b>0</b>" means low level state.</li>
<li>"value": "<b>1</b>" means high level state.</li>
</ul>
</li>{{#ifeq:{{{name}}}|RUT956|
<li><b>relay0</b> is the relay:
<ul>
<li>"state": "<b>open</b>" means open relay state.</li>
<li>"state": "<b>closed</b>" means closed relay state.</li>
</ul>
</li>|}}
</ul>
{{#ifeq:{{{name}}}|RUT956|
To change relay settings, use the <i><b>update</i></b> command and specify a state:
ubus call ioman.relay.relay0 update '{"state":"open"}'
ubus call ioman.relay.relay0 update '{"state":"closed"}'
|}}
