TRB140 LAN

From Wiki Knowledge Base | Teltonika Networks
This is the approved revision of this page, as well as being the most recent.
Main Page > TRB Gateways > TRB140 > TRB140 Manual > TRB140 WebUI > TRB140 Network section > TRB140 LAN

The information in this page is updated in accordance with firmware version TRB14X_R_00.02.03.1

Summary[edit | edit source]

The LAN page is used to to set up LAN network interfaces.

This manual page provides an overview of the LAN windows in TRB140 devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking trb14x manual webui basic advanced mode v1.gif

LAN Configuration[edit | edit source]

The LAN Configuration section displays LAN interfaces currently existing on this device.

Networking trb14x manual lan settings v1.png

To begin configuring an interface, click the 'Edit' button on the right side of the interface:

Networking trb14x manual lan begin to edit v1.png

General Setup[edit | edit source]


The General Setup section is used to configure the main parameters of

Networking trb14x manual lan configuration general setup v1.png

Field Value Description
IPv4 address ip4; default: 192.168.2.1 The IPv4 address interface of this interface. An IP address identifies a device on a network and allows it to communicate with other devices.
IPv4 netmask netmask; default: 255.255.255.0 The IPv4 netmask of this interface. A netmask is used to define how "large" a network is by specifying which part of the IP address denotes the network and which part denotes a device.
DNS servers ip4; default: none DNS server addresses that this interface will use. If left empty, DNS servers are assigned automatically. To see what DNS servers are currently used, you can check the contents of the /tmp/resolv.conf.auto file.

Advanced Settings[edit | edit source]


The Advanced Settings section is used to set up some of the more specific and less frequently used interface parameters.

Networking rutos manual lan configuration advanced settings v1.png

Field Value Description
Override MAC address mac; default: none When set, uses a user-defined MAC address for the interface.
Override MTU integer [1..9200]; default: none Changes the interface's allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.

DHCP Server[edit | edit source]


A DHCP (Dynamic Host Configuration Protocol) server is a service that can automatically configure the TCP/IP settings of any device that requests such a service. If you connect a device that has been configured to obtain an IP address automatically, the DHCP server will lease out an IP address from the available IP pool and the device will be able to communicate within the private network.

Networking rutx manual lan static dhcp server scheme v1.png

DHCP Server: General Setup[edit | edit source]


The General Setup section is used to set up the main operating parameters of the DHCP server. Networking trb14x manual lan configuration dhcp server general setup v1.png

Field Value Description
Enable DHCP Enable | Disable | DHCP Relay*; default: Enable Turns the DHCP server on or off or enables DHCP relay*.
If DHCP Relay* is selected, you will be prompted to enter an IP address of another DHCP server in your LAN. In this case, whenever a new machine connects to this device, it will redirect any DHCP requests to the specified DHCP Server.
Start integer [1..255]; default: 100 The starting IP address value. e.g., if your device’s LAN IP is 192.168.1.1 and your subnet mask is 255.255.255.0 that means that in your network a valid IP address has to be in the range of [192.168.1.0..192.168.1.254] (192.168.1.255 is a special unavailable address). If the Start value is set to 100 then the DHCP server will only lease out addresses starting from 192.168.1.100.
Limit integer [1..255]; default: 150 How many addresses the DHCP server can lease out. Continuing from the example above: if the start address is 192.168.1.100 and the server can lease out 150 addresses, available addresses will be from 192.168.1.100 to 192.168.1.249 (100 + 150 – 1 = 249; this is because the first address is inclusive).
Lease time integer [2..999999]; default: 12 A DHCP lease will expire after the amount of time specified in this field and the device that was using the lease will have to request a new one. However, if the device stays connected, its lease will be renewed after half of the specified amount of time passes (e.g., if lease time is 12 hours, then every 6 hours the device will ask the DHCP server to renew its lease).
The minimal amount of time that can be specified is 2 minutes.
Units Hours | Minutes; default: Hours Lease time measurement units.

* When an interface is set to act as a DHCP Relay, it redirects all received DHCP request messages to another specified DHCP server:

Networking rutx manual lan static dhcp server relay scheme v2.png

DHCP Server: IPv6 Settings[edit | edit source]


Refer to the table below for information on the IPv6 Settings section.

Networking rutos manual lan configuration dhcp server ipv6 settings v1.png

Field Value Description
Router Advertisement-Service disabled | relay mode | server mode | hybrid mode; default: Disabled Specifies whether router advertisements should be enabled (server mode), relayed or disabled.
DHCPv6-Service disabled | relay mode | server mode | hybrid mode; default: Disabled Specifies whether DHCPv6 server should be enabled (server), relayed (relay) or disabled (disabled).
NDP-Proxy disabled | relay mode | hybrid mode; default: Disabled Specifies whether NDP should be relayed or disabled.
DHCPv6-Mode stateless | stateful-only | stateless + stateful; default: stateless + stateful Router announcement (RA) mode.
Always announce default router off | on; default: off Default router lifetime in the the router announcement (RA) message will be set if default route is present and a global IPv6 address or if default route is present but no global IPv6 address or neither of both conditions.
Announced DNS server ip; default: none Supplements DHCP-assigned DNS server entries with ones specified in this field.
Announced DNS domains ip; default: none DNS domain handed out to DHCP clients.

Static Lease[edit | edit source]


Static IP leases are used to reserve specific IP addresses for specific devices by binding them to their MAC address. This is useful when you have a stationary device connected to your network that you need to reach frequently, e.g., printer, IP phone, etc.

This section displays static IP leases currently existing on this device.

Networking rutos manual lan lan configuration static lease v1.png

Static Lease: Settings[edit | edit source]


To access a lease's settings page, click the 'Edit' button located to the right of the lease:

Networking rutos manual lan lan configuration static lease edit v1.png

You should be directed to a window that looks like this:

Networking rutos manual lan lan configuration static lease settings v1.png

Field Value Description
MAC address mac; default: none MAC address of a device that is on this interface's network.
IP address ip; default: none The IP address that will be reserved for the specified device.

Static Lease: Add Lease[edit | edit source]


The Add Lease section is used to create new static leases. To create a new lease, simply enter a custom name for it and click the 'Add' button.

Networking rutos manual lan lan configuration static lease add lease v1.png