TRB141 Cloud Solutions

From Wiki Knowledge Base | Teltonika Networks
This is the approved revision of this page, as well as being the most recent.
Main Page > TRB Gateways > TRB141 > TRB141 Manual > TRB141 WebUI > TRB141 Services section > TRB141 Cloud Solutions

The information in this page is updated in accordance with firmware version TRB1_R_00.02.05.1.

Summary[edit | edit source]

The Cloud Solutions section is used to configure how the device will connect to certain cloud management systems. This chapter is an overview of the Cloud Solutions section for TRB141 routers.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking trb1 manual webui basic advanced mode.gif

RMS[edit | edit source]

RMS (Remote Management System) is a cloud system designed by Teltonika and intended for remote monitoring and management of Teltonika-Networks products.

In order to add a device(s) to RMS, get yourself acquainted by watching this instructional video and register an account by clicking here. Each unique device receives a free month-long RMS license when added to RMS for the first time.


The figure below is a screenshot of the RMS section taken from a device which has been connected to RMS:

Networking rutos manual setup wizard rms imei.png

Field Value Description
Connection type Enabled | Standby | Disabled; default: Enabled Defines how the device will connect to RMS:
  • Enabled - the device attempts to connect to RMS every 2-5 minutes (every 2 minutes the first hour; then every 5 minutes). If it cannot connect for 14 days, it will enter Standby mode.
  • Standby - the device attempts to connect to RMS every 6 hours.
  • Disabled - RMS functionality is disabled.
Hostname host | ip; default: rms.teltonika.lt Address of the RMS server. If you're using regular RMS, just leave the default address (rms.teltonika.lt).
Port integer [0..65535]; default: 15009 Port number for connecting to RMS. If you're using regular RMS, just leave the default port (15009).



The RMS server waits for incoming connections. Since the device attempts to connect at a fixed interval, it may not connect instantly after you add it to RMS. While it is disconnected, you can check how much time is left until the next connection attempt in the Status section:

Networking rutos manual cloud solutions rms disconnected rms imei.png

To speed up the process by initiating an immediate connection attempt, click the 'Connect' button.

For more information on Teltonika Networks Remote Management System (RMS) refer to the RMS Manual or RMS FAQ pages.

Azure IoT Hub[edit | edit source]

Azure IoT Hub is Microsoft's ever-expanding set of cloud services to help your organization meet your business challenges. Azure IoT Hub is compatible with Teltonika Networks devices.

The figure and table below provides explanations for Azure IoT Hub configuration parameters when selected 'Message Type' is GSM values.

Networking rutos manual cloud solutions azure iot hub modem 1.png

Field Value Description
Enable Azure IoT Hub monitoring off | on; default: off Turns the Azure IoT Hub service on or off.
Connection string string; default: none Unique connection string a.k.a. server address provided by the Azure Iot Hub service.
Message Type GSM values | MQTT messages; default: GSM values Values that are to be sent to the Azure server.
Message sending interval (sec.) integer; default: 300 Device data sending frequency in seconds. Minimum value is 10 s.
Mobile Interface mobile interface; default: mobs1a1 Interface name for which IP address and sent/received bytes should be selected.
GSM Values IMSI | IP Address | RSRP | ICCID | Bytes received | Cell ID | RSCP | PIN state | Manufacturer | Bytes sent | RSRQ | Revision number | Serial number | ECIO | SINR |Data carrier type | Network link state | Operator | PIN count | Signal level | Model | Connection state | Temperature | IMEI | SIM card state; default: none Selects the mobile connection values that to be sent to the Azure IoT Hub service.

The figure and table below provides explanations for Azure IoT Hub configuration parameterswhen selected 'Message Type' is MQTT messages.

Networking rutos manual cloud solutions azure iot hub modem 0.png

Field Value Description
Enable Azure IoT Hub monitoring off | on; default: off Turns the Azure IoT Hub service on or off.
Connection string string; default: none Unique connection string a.k.a. server address provided by the Azure Iot Hub service.
Message Type GSM values | MQTT messages; default: GSM values Values that are to be sent to the Azure server.
MQTT Host ip | host; default: none MQTT broker's IP address or hostname.
MQTT Port integer [0..65535]; default: none MQTT broker's IP port number.
Topic string; default: none MQTT topic to be used for publishing the data.
Username string; default: none Username used for authentication to the MQTT broker.
Password string; default: none Password used for authentication to the MQTT broker.

Cloud of Things[edit | edit source]

Cloud of Things is a cloud platform for the Internet of Things (IoT). It allows you to remotely monitor, manage and control your connected devices and machines – plug-and-play, without extensive installation.

Networking rutos manual cloud solutions cloud of things modem 1.png

Field Value Description
Enable off | on; default: off Turns the Cloud of Things service on or off.
Server Address ip | host; default: none Cloud of Things server IP address or hostname.
Interval integer; default: none Push connection interval in minutes.
Mobile Interface mobile interface; default: mobs1a1 Interface name for which IP address and sent/received bytes should be selected.
Reset Auth - (interactive button) Reset authentication data so that device could be re-registered on the Cloud of Things Device Management platform.

Cumulocity[edit | edit source]

Cumulocity IoT is a cloud-based, real-time IoT management platform that's also compatible with Teltonika-Networks devices.

The figure and table below provides explanations for Cumulocity configuration parameters. For a detailed configuration guide, click here.

Networking rutos manual cloud solutions cumulocity modem 1.png

Field Value Description
Enable off | on; default: off Turns the Cumulocity service on or off.
Use SSL/TLS off | on; default: off Turn SSL/TLS protocol support on or off.
Server Address host; default: none Your Cumulocity server's hostname. It should match the Environment name from the Cumulocity registration.
For example: teltonika-networks.eu-latest.cumulocity.com
Interval integer; default: none Connection push interval in minutes. This field defines how often the device will try to connect to the Cumulocity server.
Mobile Interface network interface; default: mob1s1a1 Interface whose GSM parameters will be sent to the Cumulocity server for monitoring.
Reset Auth - (interactive button) Resets authentication for this device. If you click this, you'll have to authorize this from Cumulocity dashboard before it can successfully connect to the server.

ThingWorx[edit | edit source]

Networking rutos manual cloud solutions thingworx modem 1.png

Field Value Description
Enable off | on; default: off Turns the ThingWorx service on or off.
Server Address ip | host; default: none Thingworx server IP address or hostname.
Server Port integer [0..65535]; default: none Thingworx server's port number.
Thing Name string; default: none Thing name defined in ThingWorx CP.
Application Key string; default: none Application key generated in ThingWorx CP.
Mobile Interface network interface; default: mob1s1a1 Interface whose GSM parameters will be sent to the ThingWorx server for monitoring.