TSW212 Ports

From Teltonika Networks Wiki
Main Page > TSW Switches > TSW212 > TSW212 Manual > TSW212 WebUI > TSW212 Network section > TSW212 Ports

The information in this page is updated in accordance with firmware version .

Summary

The Ports page provides information related to the status of the device's physical ports, as well as the ability to edit port settings, security, loopback detection.

General

In this section you can enable Jumbo frames and LLDP frame filter services.

Networking tswos manual ports general v2.png

Field Value Description
Jumbo frames off | on; default: on Allow ethernet frame with a payload greater than the standard maximum transmission unit (MTU) of 1500 bytes. This may improve network performance by making data transmissions more efficient.
LLDP frame filter off | on; default: off Enable to stop the forwarding of LLDP frames.
IGMP snooping off | on; default: off Enables IGMP snooping.
Multicast querier off | on; default: off Enables multicast querier.

Port Settings

This section displays information about the status of the device's ports with the ability to configure port settings.

Port Settings


The figure below is an example of the All Ports window, color indicates port speed and status:

Networking tswos manual ports ports settings port settings 0.png

To change port settings select port and press `edit (number of ports) ports` button:

Networking tswos manual ports ports settings port settings edit 0.png

You will be redirected to `Port settings`. From here you can enable/disable ports or change settings:

Networking tswos manual ports ports settings port settings settings 0.png

Field Value Description
Enable off | on; default: on Toggle port on or off.
EEE off | on; default: on Enable Energy-Efficient Ethernet.
Isolate port off | on; default: off When enabled port will be isolated from other isolated ports. Traffic between isolated ports will droped. Traffic between isolated and normal ports will be sent as normal.
Link speed Auto | 10Mbps (E) | 100Mbps (FE) | 1000Mbps (GbE); default: Auto A measure of how fast ports are able to transmit and receive data.
Duplex Full | Half; default: Advertises preferred duplex mode and speed for negotiation with other devices.

Port Status


This section displays port status information. There is also an option to select, enable ports, enable/disable PoE, EEE and Isolation options:

Networking tswos manual ports ports settings port status 0.png

Field Name Description
Port Port ID.
Enabled Enable/Disable port.
Status Port status.
Speed Port link speed.
  • Possible speeds:
  • GbE: 1000Mbps
  • FE: 100Mbps
  • E: 10Mbps
  • PoE (W) PoE port power usage in watts.
    EEE Enable/Disable Energy-Efficient Ethernet.
    Isolation When enabled port will be isolated from other isolated ports. Traffic between isolated ports will be droped. Traffic between isolated and normal ports will be sent as normal.
    TX sum Total upload.
    RX sum Total download.
    TX rate Upload speed.
    RX rate Download speed.

    Port Mirroring

    Port Mirroring is a service that mirrors incoming and outgoing packets on one Ethernet port (Source Port) to another (Monitoring Port).

    To change port mirroring settings select port and press `Edit` button:

    Networking tswos manual ports port mirroring edit.png

    You will be redirected to `Port mirroring settings`, from here you can select ingress and egress ports:

    Networking tswos manual ports port mirroring configuration.png

    Field Value Description
    Enable off | on; default: off The port which will mirror the packets.
    Ingress mirroring port list port; default: none Specify which port incoming traffic is mirrored.
    Egress mirroring port list port; default: none Specify which port outcoming traffic is mirrored.

    Loopback Detection

    Loopback Detection


    A port-based loopback detection service that using its own distinctive packets, seeks to identify and break a network loop by shutting down troublesome ports.

    Networking tswos manual ports loopback detection.png

    Field Value Description
    Enable off | on; default: off Enable loopback detection.
    Broadcast interval integer [1..10000]; default: none Send detection packets in an given interval from 1 to 10000 seconds.
    Auto-recovery interval integer [60..10000]; default: none Restores disabled ports in an given interval from 60 to 10000 seconds.

    Port Tracking


    Tracks specific port status. Notes:

  • STP: STP must be disabled in Network -> Spanning Tree and loopback detection must be enabled for the service to function.
  • Port unblocking: When a loop occurs before a broadcast, it won't be recognized until the broadcast transmits its own packets, since the service only listens for packets with its own particular protocol.
  • Networking tswos manual ports loopback detection port tracking.png To change port tracking setting press on port and you will be redirected to `Port tracking configuration`: Networking tswos manual ports loopback detection port tracking configuration.png

    Field Value Description
    Enable off | on; default: on Enable port tracking.
    Recovery mode Auto | Manual; default: Auto Manages port unblocking type.Possible modes:
  • Manual: Port is blocked until manual unblock.
  • Auto: Unblocked automatically depending on the global Auto-recovery interval value.
  • Port Security

    This section displays information about the status of the device's ports with the ability to configure port security settings.

    General

    Port Settings


    The figure below is an example of the Port Settings window, color indicates port speed and status:

    Networking tswos manual ports port security port settings 0.png

    To change port security settings select port and press `edit (number of ports) ports` button:

    Networking tswos manual ports port security port settings edit 0.png

    You will be redirected to `Port security settings`. From here you can enable/disable ports or change security settings:

    Networking tswos manual ports port security port settings settings v2.png

    Field Value Description
    Enable off | on; default: off Enable security for port.
    Radius sever radius server ID; default: example Radius server ID.
    Radius unreachable action Accept | Reject; default: Accept "Accept" gives anyone access to the port when the radius server is unreachable. "Reject" only unblocks the port if radius server explicitly authorizes it.
    Fallback VLAN Disabled | VLAN; default: Disabled Indicates fallback VLAN
    Reject VLAN Disabled | VLAN; default: Disabled Indicates reject VLAN
    Accept VLAN Radius assigned | vlan1(ID: 1); default: vlan1(ID: 1) Indicates accept VLAN

    Port Status


    This section displays port status information. There is also an option to select, enable ports security, choose RADIUS server and change RADIUS unreachable action:

    Networking tswos manual ports port security port status.png

    Field Name Description
    Port Port ID.
    Enabled Enables port security on this port.
    Status Port status.
    Radius server Authenticates and authorizes devices trying to connect to this port.
    Radius unreachable action "Accept" gives anyone access to the port when the radius server is unreachable. "Reject" only unblocks the port if radius server explicitly authorizes it.

    RADIUS

    The RADIUS page is used to create and manage radius servers:

    Networking tswos manual ports port security radius.png

    Field Name Description
    ID RADIUS server ID.
    Address (IPv4) RADIUS server IP.
    Authentication port RADIUS server athentication port.
    Secret RADIUS server secret.

    Radius Configuration


    The RADIUS configuration window should look similar to this:

    Networking tswos manual ports port security radius configuration.png

    Field Value Description
    Address (IPv4/IPv6) ip; default: 0.0.0.0 RADIUS server IP.
    Authentication port interger [1.. 65535]; default: 1812 RADIUS server athentication port.
    Secret string; default: - RADIUS server secret.
    Test connectivity -(interactive) button Test connectivity to RADIUS server.
    Test user credentials -(interactive) button Test credentials to RADIUS server.
    Enable backup RADIUS server off | on; default: off Enable backup RADIUS server.
    Address (IPv4/IPv6) ip; default: none Backup RADIUS server IP.
    Authentication port interger [1.. 65535]; default: none Backup RADIUS server athentication port.
    Secret string; default: - Backup RADIUS server secret.
    Test connectivity -(interactive) button Test connectivity to backup RADIUS server.
    Test user credentials -(interactive) button Test credentials to backup RADIUS server.