Template:Networking rut manual tr-069

From Teltonika Networks Wiki
This is the approved revision of this page, as well as being the most recent.

The information in this page is updated in accordance with the [[Media:_WEBUI.bin|]] firmware version.

Summary[edit source]

TR-069 (Technical Report 069) is an application layer protocol designed for management of equipment connected to a remote network.

This chapter of the user manual provides an overview of the UPnP page in {{{name}}} devices.


TR-069 is additional software that can be installed from the Services → [[{{{name}}} Package Manager|Package Manager]] page. The 'Package Manager' service is available from FW version

TR-069 Client Configuration[edit source]

Networking rutxxx manual tr-069 client configuration v1.png

Field Value Description
Enable yes | no; default: no Turns TR-069 client on or off.
Periodic enable yes | no; default: yes Turns periodic data transmissions to server on or off.
Accept server request yes | no; default: no When enabled the router accepts connection requests from server.
Sending interval integer [60..9999999]; default: 100 Periodic data transmission frequency (in seconds).
Username string; default: easycwmp Username used for authentication to a TR-069 server.
Password string; default: easycwmp Password used for authentication to a TR-069 server.
URL host | ip; default: http://192.168.1.110:8080/openacs/acs IP address or hostname of a TR-069 server.

Management via TR-069[edit source]

TR-069 can be used to set or get values from RUT routers. Below is a list of commands used for router management via TR-069.

  • R - read only;
  • RW - read/write;
  • string(64) - 64 bit string;
  • string(256) - 256 bit string;
  • unsignedInt - integer storing only positive values.

FW Upgrade:

 1. FileType - firmware Upgrade Image, string(64)
 2. URL - URL, specifying the source file location, string(256) 
 3. Username - username to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256) 
 4. Password - password to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256)
 5. FileSize - the size of the file to be downloaded in bytes, unsignedInt 

Device Information:

 1. DeviceInfo.SpecVersion - R
 2. DeviceInfo.ProvisioningCode - RW
 3. DeviceInfo.Manufacturer - device manufacturer (e.g., Teltonika) R
 4. DeviceInfo.ManufacturerOUI - R
 5. DeviceInfo.ProductClass - device model (e.g., {{{name}}}) R
 6. DeviceInfo.SerialNumber - device serial number (e.g., 1000111111) R
 7. DeviceInfo.HardwareVersion - device hardware version (e.g., 0505) R
 8. DeviceInfo.SoftwareVersion - device software version (e.g., {{{fw_version}}}) R
 9. DeviceInfo.UpTime - router uptime R
 10. DeviceInfo.DeviceLog - last line of device log. R
 11. DeviceInfo.MemoryStatus
   11.1 DeviceInfo.MemoryStatus.Total - total device memory (e.g., 61008) R
   11.2 DeviceInfo.MemoryStatus.Free - free memory (e.g., 24224) R

IP Ping Diagnostics support:

 1. IPPingDiagnostics
   1.1 IPPingDiagnostics.DiagnosticsState - diagnostics State (e.g. None) R
   1.2 IPPingDiagnostics.Host - host RW
   1.3 IPPingDiagnostics.NumberOfRepetitions - number of repetitions RW
   1.4 IPPingDiagnostics.Timeout - timeout RW
   1.5 IPPingDiagnostics.DataBlockSize - data block size RW
   1.6 IPPingDiagnostics.SuccessCount - success count R
   1.7 IPPingDiagnostics.FailureCount - fail count R
   1.8 IPPingDiagnostics.AverageResponseTime - average response time R
   1.9 IPPingDiagnostics.MinimumResponseTime - minimum response time R
   1.10 IPPingDiagnostics.MaximumResponseTime - maximum response time R

Mobile Information:

 1.MobileInfo
   1.1 MobileInfo.RSSI - GSM signal level R
   1.2 MobileInfo.ConnState - connection state R
   1.3 MobileInfo.NetState - network link state R
   1.4 MobileInfo.ICCID - SIM ICCID R
   1.5 MobileInfo.IMSI - IMSI R
   1.6 MobileInfo.RSCP - RSCP level R
   1.7 MobileInfo.ECIO - EC/IO level R
   1.8 MobileInfo.RSRP - RSRP level R
   1.9 MobileInfo.SINR - SINR level R
   1.10 MobileInfo.RSRQ - RSRQ level R
   1.11 MobileInfo.CellID - CellID R
   1.12 MobileInfo.Operator - mame of operator used R
   1.13 MobileInfo.OperatorNum - operator number R
   1.14 MobileInfo.ConnType - data carrier type R
   1.15 MobileInfo.Modem
     1.15.1 MobileInfo.Modem.Model - modem model R
     1.15.2 MobileInfo.Modem.Manufacturer - modem manufacturer R
     1.15.3 MobileInfo.Modem.Serial - modem serial number R
     1.15.4 MobileInfo.Modem.Revision - modem revision number R
     1.15.5 MobileInfo.Modem.IMEI - modem IMEI R
     1.15.6 MobileInfo.Modem.SimState - SIM card state R
     1.15.7 MobileInfo.Modem.PinState - PIN state R
     1.15.8 MobileInfo.Modem.Temperature - modem temperature in 0.1 degrees Celsius R
 1.16 MobileInfo.SentToday - bytes sent today R
 1.17 MobileInfo.ReceivedToday - bytes received today R
 1.18 MobileInfo.SentThisMonth - bytes sent this month R
 1.19 MobileInfo.ReceivedThisMonth - bytes received this month R

WAN Information:

 1. WANConnectionDevice
   1.1 WANConnectionDevice.WANIPConnection
     1.1.1 WANConnectionDevice.WANIPConnection.ConnectionStatus - connection status (e.g., Connected) R
     1.1.2 WANIPConnection.ExternalIPAddress - IP address R
     1.1.3 WANIPConnection.MACAddress - MAC address R
   1.2 WANConnectionDevice.WANPPPConnection - PPP connection
     1.2.1. WANConnectionDevice.WANPPPConnection.1.Enable - connection state (e.g., 1 or 0) R
     1.2.2. WANConnectionDevice.WANPPPConnection.1.APN - APN R
     1.2.3. WANConnectionDevice.WANPPPConnection.1.ExternalIPAddress - IP address R

WiFi Information:

 1. Radio
   1.2 Radio.Enable - enabled (e.g., 0 or 1) RW
   1.3 Radio.Status - WiFi status (e.g., Up) R
   1.4 Radio.Name - Device name R
   1.5 Radio.SupportedFrequencyBands - supported frequency bandss (e.g., 2.4GHz) R
   1.6 Radio.OperatingFrequencyBand - operating frequency bandss (e.g., 2.4GHz) R
   1.7 Radio.ChannelsInUse - channels R
   1.8 Radio.Channel - channel in use RW
   1.9 Radio.AutoChannelSupported - auto channel support (e.g., 1) R
   1.10 Radio.AutoChannelEnable - auto channel state (e.g., 1) RW
   1.11 Radio.OperatingStandards - operating standards (e.g., 11ng) RW
 2. SSID
   2.1 SSID.Enable - WiFi interface state (e.g., 1) RW
   2.2 SSID.Status - WiFi interface status (e.g., 1) R
   2.3 SSID.Name - interface name (e.g., wlan0 ) R
   2.4 SSID.SSID - SSID RW
 3. Security
   3.5 Security.ModesSupported - (None,WEP-64,WEP-128,WPA-Personal,WPA2-Personal,WPA-WPA2-Personal,WPA-Enterprise,WPA2-Enterprise,WPA-WPA2-Enterprise) R
   3.6 Security.ModeEnabled - current mode (e.g WPA2-Personal) RW
   3.7 Security.WEPKey - WEP key RW
   3.8 Security.PreSharedKey - pre-shared key RW
   3.9 Security.KeyPassphrase - key passphrase RW

Hotspot information:

 1. General
   1.1 General.Enable - state (e.g. 1) RW
   1.2 General.IP - IP address (e.g. 192.168.2.254) RW
   1.3 General.Mode - authentication mode
         (extrad - External radius, intrad - Internal radius, norad - Without radius, add - Advertisement, mac - MAC auth, sms - SMS OTP) (e.g., norad) RW
   1.4 General.ExternalLandingPage - enable external landing page (e.g., 1) RW
   1.5 General.LandingPageAddress - external landing page address (e.g., www.landingpageaddr.com) RW
   1.6 General.HTTPSRedirect - enable HTTPS redirect RW
 2. Radius
   2.1 Radius.Server1 - first radius server address RW
   2.2 Radius.Server2 - second Radius server address RW
   2.3 Radius.AuthenticationPort - authentication port RW
   2.4 Radius.AccountingPort - accounting port RW
   2.5 Radius.RadiusSecretKey - radius secret key RW
   2.6 Radius.UAMPort - UAM port RW
   2.7 Radius.UAMUIPort - UAM UI port RW
   2.8 Radius.UAMSecret - UAM secret RW
   2.9 Radius.NASIdentifier - NAS identifier RW
   2.10 Radius.SwapOctets - swap octets RW
   2.11 Radius.LocationName - location name RW

Management server information:

 1. ManagementServer.URL - server url (e.g., http://192.168.1.110:8080/openacs/acs) RW
 2. ManagementServer.Username - username (e.g., easycwmp) RW
 3. ManagementServer.Password - password (e.g., easycwmp) RW
 4. ManagementServer.PeriodicInformEnable - enable periodic inform (e.g., 1 or 0) RW
 5. ManagementServer.PeriodicInformInterval - interval (e.g, 100) RW
 6. ManagementServer.PeriodicInformTime - inform time (e.g, 0001-01-01T00:00:00Z) RW

[[Category:{{{name}}} Services section]]