Line 27: |
Line 27: |
| ----First of all, lets configure the VPN IPsec instance from RUTX11's side: | | ----First of all, lets configure the VPN IPsec instance from RUTX11's side: |
| *Login to the router's WebUI and go to '''Services → VPN → IPsec'''. Enter a custom name (for this example we use ''test'') for the IPsec instance click the "Add" button: | | *Login to the router's WebUI and go to '''Services → VPN → IPsec'''. Enter a custom name (for this example we use ''test'') for the IPsec instance click the "Add" button: |
− | [[File:IPsec RUTOS RUTX11 Instance.png|alt=|993x993px|border|class=tlt-border]] | + | [[File:IPsec RUT955 instance2.png|alt=|border|992x992px]] |
| ---- | | ---- |
| *Click the "Edit" button located next to the newly created instance and set up the configuration according to the network: | | *Click the "Edit" button located next to the newly created instance and set up the configuration according to the network: |
− | [[File:Wiki3.png|alt=|center|930x930px|border|class=tlt-border]] | + | [[File:IPsec RUT955 config 2.png|alt=|border|center|930x930px]] |
| *Below are explanations of the parameters highlighted in the figure above. Other parameters (not highlighted) are defaults. You can find descriptions for these parameters in the '''[[VPN#IPsec|VPN manual page, IPsec section]]''' | | *Below are explanations of the parameters highlighted in the figure above. Other parameters (not highlighted) are defaults. You can find descriptions for these parameters in the '''[[VPN#IPsec|VPN manual page, IPsec section]]''' |
| **'''Enable''' - enables the IPsec instance | | **'''Enable''' - enables the IPsec instance |
Line 44: |
Line 44: |
| | | |
| *IKE lifetime must be added and can be any desired value. | | *IKE lifetime must be added and can be any desired value. |
− | [[File:IPsec RUTX11 Phase 1.png|center|714x714px|class=tlt-border|alt=]] | + | [[File:IPsec RUT955 phase 12.png|alt=|center|714x714px]] |
− | | |
| * Phase 1 & Phase 2 details should be the same with that of the RUT955 P1 & P2 details or else the tunnel will not be properly established. | | * Phase 1 & Phase 2 details should be the same with that of the RUT955 P1 & P2 details or else the tunnel will not be properly established. |
− | [[File:IPsec RUTX11 Phase 2.png|center|719x719px|border|class=tlt-border|alt=]] | + | [[File:IPsec RUTX11 Phase 22.png|alt=|border|center|719x719px]] |
| | | |
| ===RUT955=== | | ===RUT955=== |
| ----Similarly, the configuration for the VPN IPsec instance from RUT955's side is as follows: | | ----Similarly, the configuration for the VPN IPsec instance from RUT955's side is as follows: |
| | | |
− | [[File:IPsec RUT955 instance.png|alt=|993x993px|border|class=tlt-border]] | + | [[File:IPsec RUT955 instance2.png|alt=|border|992x992px]] |
| | | |
| *In this case, Remote endpoint should be RUTX11's Public IP: | | *In this case, Remote endpoint should be RUTX11's Public IP: |
− | | + | [[File:IPsec RUTX11 Config2.png|alt=|center|762x762px]] |
− | [[File:IPsec RUT955 config.png|center|762x762px|class=tlt-border|alt=]] | |
| ---- | | ---- |
| * The last step in configuring the IPsec instances is '''Phase settings'''. Make sure they match with the Phase settings (both Phase 1 and Phase 2) of the RUTX11's connection: | | * The last step in configuring the IPsec instances is '''Phase settings'''. Make sure they match with the Phase settings (both Phase 1 and Phase 2) of the RUTX11's connection: |
− | [[File:IPsec RUT955 phase 1.png|alt=|center|789x789px|border|class=tlt-border]] | + | [[File:IPsec RUT955 phase 12.png|alt=|border|center|789x789px]] |
− | [[File:IPsec RUT955 phase 2.png|center|734x734px|border|class=tlt-border|alt=]] | + | [[File:IPsec RUTX11 Phase 22.png|alt=|border|center|734x734px]] |
| | | |
| | | |
Line 69: |
Line 67: |
| [[File:IPsec RUTX11 result 2.png|alt=|border|902x902px]] | | [[File:IPsec RUTX11 result 2.png|alt=|border|902x902px]] |
| [[File:IPsec RUT955 result 2.png|alt=|left|903x903px]] | | [[File:IPsec RUT955 result 2.png|alt=|left|903x903px]] |
| + | |
| + | |
| + | |
| | | |
| | | |