Difference between revisions of "OTD140 LEDs"
(Created page with "{{Template: Networking_rutos_manual_leds <!------------------------DEVICE-----------------------> | name = OTD140 | series = OTD140 <!----------------------SEPARAT...") |
|||
| Line 4: | Line 4: | ||
| series = OTD140 | | series = OTD140 | ||
<!----------------------SEPARATORS---------------------> | <!----------------------SEPARATORS---------------------> | ||
| − | | 2g = | + | | 2g = 1 <!-- 1 has 2G; 0 doesn't have 2G --> |
| − | | 5g = | + | | 5g = 0 <!-- 1 has 5G; 0 doesn't have 5G --> |
| eth = 1 <!-- 1 has ETH; 0 doesn't have ETH --> | | eth = 1 <!-- 1 has ETH; 0 doesn't have ETH --> | ||
| eth_leds = 2 <!-- 1 for green; 2 for green & orange --> | | eth_leds = 2 <!-- 1 for green; 2 for green & orange --> | ||
| mobile = 1 <!-- 1 has mobile; 0 doesn't have mobile --> | | mobile = 1 <!-- 1 has mobile; 0 doesn't have mobile --> | ||
| mobile_leds = 3 <!-- number of mobile signal strength type LEDs --> | | mobile_leds = 3 <!-- number of mobile signal strength type LEDs --> | ||
| − | | power_leds = | + | | power_leds = 2 <!-- number of power LEDs --> |
| − | | wan = | + | | wan = 0 <!-- 1 has WAN type LEDs; 0 doesn't have WAN type LEDs --> |
| − | | wifi = | + | | wifi = 0 <!-- 1 has WiFi band LEDs; 0 doesn't have WiFi band LEDs --> |
}} | }} | ||
Revision as of 11:55, 9 January 2024
Main Page > OTD Outdoor routers > OTD140 > OTD140 Manual > OTD140 LEDsThis page contains information the different types of LEDs and their behaviour on a OTD140 device.
Power LED
The power LED's are located on the each Ethernet ports (POE In/POE Out). Green PD (Power Device) LED shines when power is supplied to device PoE In port. Green PSE (Power Sourcing Equipment) activity LED shines when PD device is connected to PoE Out port.
It indicates whether the device is powered on or not.
Ethernet port LEDs
There are two LEDs located at the top of each Ethernet port.
They provide information on the current states of the Ethernet ports. Each port has two LEDs:
- Orange - 10/100 Mbps connection
- Green- power LED
Below is an explanation on the behaviours of green and orange LEDs.
| State | Description |
|---|---|
| Yellow LED on | A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred). |
| Yellow LED off | No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card). |
| Yellow LED blinking | Connection established and data is being transferred over this port. |
| Green LED on | Power ON. |
| Green LED off | Power OFF. |
| Green LED blinking | Power supply/device being disrupted or not stable. |
Mobile network type LEDs
The mobile network type LEDs are located near the SIM card slot.
They display which type of Internet connection is currently active.
| Action | Description |
|---|---|
| 2G LED turned on | Device is connected to a 2G network. |
| 3G LED turned on | Device is connected to a 3G network. |
| 4G LED turned on | Device is connected to a 4G network. |
| 2G blinking | Device is connected to a 2G network but hasn't received an IP address. |
| 3G blinking | Device is connected to a 3G network but hasn't received an IP address. |
| 4G blinking | Device is connected to a 4G network but hasn't received an IP address. |
| All LEDs blinking at the same time every 500 ms | No SIM card or incorrect PIN. |
| All LEDs turn on and off in a sequence one after the other | The device is attempting to connect to a mobile network operator. |
Mobile signal strength indication LEDs
The mobile signal strength indication LEDs are located near the SIM card slot.
The number of lit up LEDs represents a different mobile signal strength (RSSI) value in dBm.
| No. of lit up LEDs | Signal strength value |
|---|---|
| 0 | ≤ -111 dBm |
| 1 | -110 dBm to -82 dBm |
| 2 | -81 dBm to -52 dBm |
| 3 | ≥ -51 dBm |
The Mobile signal strength LEDs can also be used as a time indicator for holding the reset button. When you press and hold the reset button, if there is a User's default configuration configured on the device, you have to hold it pressed for 6 seconds (by default) to initiate a User's default configuration reset and 12 seconds (by default) to initiate a Factory reset. Otherwise, it is only necessary to hold the reset button for 6 seconds to trigger a Factory reset. If the button was held down longer than 20 seconds (by default) no action will be taken.
While holding the reset button each lit up signal strength LED indicate that a period of two seconds has passed. In case with OTD140, when all 3 Mobile signal strength LEDs are lit up, they represent that 6 (LED number multiplied by 2) seconds have passed since you pressed down on the reset button.
After releasing the button at one of the reset periods, all 3 LEDs will start blinking every 1 second. This signifies that the router has begun the reset.
