RUT200 Network

From Teltonika Networks Wiki
Main Page > RUT Routers > RUT200 > RUT200 Manual > RUT200 WebUI > RUT200 Status section > RUT200 Network

The information in this page is updated in accordance with firmware version RUT2M_R_00.07.04.5.


The Network page contains information related to the device's networking. This chapter is an overview of the Network page in RUT200 devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

Networking rut2m manual webui basic advanced mode.gif


The Mobile tab displays information about the mobile connection. The figure below is an example of the Mobile tab: Networking trb14x manual network v3.png

field name description
IMEI The IMEI (International Mobile Equipment Identity) is a unique 15 decimal digit number used to identify mobile modules. GSM network operators use the IMEI to identify devices in their networks
SIM card state The current SIM card state. Possible values are:
  • Inserted - SIM card is inserted and ready to be used
  • Not inserted - SIM card is not inserted
  • Unknown - unable to obtain SIM card state value. Possible communication issue between the the device and the modem
IMSI The IMSI (international mobile subscriber identity) is a unique 15 decimal digit (or less) number used to identify the user of a cellular network
ICCID SIM card's ICCID - a unique serial number used to identify the SIM chip
Operator Network operator's name
Operator state Shows whether the network has currently indicated the registration of the mobile device. Possible values are:
  • Unregistered - not registered to a network and the device is not currently searching for a new operator to register to
  • Registered (home) - registered, home network
  • Searching - not registered to a network, but the device is currently searching for a new operator to register to
  • Network denied - registration to network denied by operator
  • Unknown - operator state is currently unknown
  • Registered (roaming) - registered to network, roaming conditions
Cell ID The ID of the cell that the modem is currently connected to
Data connection state Indicates whether the device has a mobile data connection or not
Network type Mobile network type. Possible values are:
  • 4G: 4G (LTE)
  • 3G: 3G (WCDMA), 3G (HSDPA), 3G (HSUPA), 3G (HSPA), 3G (HSPA+), 3G (DC-HSPA+), 3G (HSDPA+HSUPA), UMTS
  • N/A - not possible to determine at the moment
Signal strength Received signal strength indicator (RSSI) measured in dBm. Values closer to 0 indicate a better signal strength
Carrier Aggregation LTE Advanced Carrier Aggregation, CA, is one of the key techniques used to enable the very high data rates of 4G to be achieved.

By combining more than one carrier together, either in the same or different bands it is possible to increase the bandwidth available and in this way increase the capacity of the link.

Connected band Currently used mobile frequency band.
Other signal level measurements Overall signal quality for different network types is defined by different measurements. Short explanations and recommendations are provided below. Click here for more in-depth information or click on one of the links below:
    • 4G
      • RSRP - reference signal received power, measured in dBm. Values closer to 0 indicate better signal strength
      • RSRQ - reference signal received quality, measured in dB. Values closer to 0 indicate a better rate of information transfer
      • SINR - signal-to-interference-plus-noise ratio, measured in dB. Higher values indicate a better rate of information transfer
    • 3G
      • EC/IO - downlink carrier-to-interference ratio. Values range from -20 to 0 (closer to 0 indicates better signal quality/cleanliness)
      • RSCP - received signal code power. Values range from -124 to 0 (closer to 0 indicates better signal stength)
Bytes received Amount of data received through the mobile interface
Bytes sent Amount of data sent through the mobile interface
Restart Modem Restarts the devices module


This tab displays information about the device's local network(s). The figure below is an example of the Network window:

Networking rutos manual network lan v2.png

lan information
Name LAN interface name
IP address IP address of the LAN interface
Netmask Netmask of the LAN interface. In a sense, a netmask specifies the size of a network. In other words, it indicates which part of the IP address denotes the network, and which denotes the device
dhcp leases
Hostname Hostname of a LAN client
IP Address IP address of a LAN client
MAC Address MAC address of a LAN client
Leasetime Remaining Remaining lease time for a DHCP client. Active DHCP lease holders will try to renew their DHCP leases after a half of the lease time passes.


Networking rutos manual status network wifi 1 v1.png

Field name Description
SSID The broadcasted SSID (Service Set Identifier) of the wireless network
Wireless MAC The MAC (Media Access Control) address of the access point radio
Band The band defines which frequency used
Signal The signal quality between router's radio and some other device that is connected to the router
Bit rate The maximum possible physical throughput that the router's radio can handle. Bit rate will be shared between router and other possible devices which connect to local Access Point (AP)
Mode Connection mode. Can either be Access Point (AP) or Client. In AP mode others can connect to this router's wireless connection. In client mode router connects to other wireless networks
Encryption The type of WiFi encryption used
Hostname Device's hostname
IP address Shows what IP address leased for device
MAC address Device's MAC (Media Access Control) address
Signal Received Signal Strength Indicator (RSSI). Signal's strength measured in dBm
RX rate The rate at which packets are received from associated interface
TX rate The rate at which packets are sent to associated interface