Line 31: |
Line 31: |
| * On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port. | | * On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port. |
| * After performing these actions press <strong>Save & Apply</strong> in VLAN settings. | | * After performing these actions press <strong>Save & Apply</strong> in VLAN settings. |
− | [[File:Network RUTOS manual lan as wan vlan.png|border|class=tlt-border|1102px]] | + | [[File:VLAN config.png|border|center|class=tlt-border|798x239px]] |
− | | |
| ===Add new WAN interface=== | | ===Add new WAN interface=== |
| ---- | | ---- |
Line 39: |
Line 38: |
| * Enter new <strong>Interface Name</strong>. | | * Enter new <strong>Interface Name</strong>. |
| * Click on <strong>Add</strong> button. | | * Click on <strong>Add</strong> button. |
− | [[File:Network RUTOS manual lan as wan create interface.png|border|class=tlt-border|1102px]] | + | [[File:New interface.png|border|center|class=tlt-border|901x453px]] |
| ---- | | ---- |
| | | |
Line 45: |
Line 44: |
| * Choose <strong>DHCP</strong> Protocol from drop-down list. | | * Choose <strong>DHCP</strong> Protocol from drop-down list. |
| * Press on <strong>Switch Protocol</strong>. | | * Press on <strong>Switch Protocol</strong>. |
− | [[File:Network RUTOS manual lan as wan interface setup dhcp.png|border|class=tlt-border|1102px]] | + | [[File:DHCP settings.png|border|center|class=tlt-border|870x261px]] |
| If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify: | | If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify: |
| * IPv4 address | | * IPv4 address |
Line 52: |
Line 51: |
| * IPv4 broadcast | | * IPv4 broadcast |
| * DNS servers | | * DNS servers |
− | [[File:Network RUTOS manual lan as wan interface setup static_v2.png|border|class=tlt-border|1102px]] | + | [[File:Static IP.png|border|center|class=tlt-border|848x351px]] |
| ---- | | ---- |
| | | |
| After switching protocol More setting options will appear. | | After switching protocol More setting options will appear. |
| * Go to <strong>Physical Settings</strong>. | | * Go to <strong>Physical Settings</strong>. |
− | * From drop-down list choose previously created VLAN interface (in this example it is eth0.300) | + | * From drop-down list choose previously created VLAN interface (in this example it is eth0.3) |
| * Press <strong>Apply & Save</strong>. | | * Press <strong>Apply & Save</strong>. |
− | [[File:Network RUTOS manual lan as wan interface physical settings.png|border|class=tlt-border|1102px]] | + | [[File:Physical interface.png|border|center|class=tlt-border|866x281px]] |
| | | |
| ===Set/Check Firewall=== | | ===Set/Check Firewall=== |
Line 65: |
Line 64: |
| | | |
| Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone. | | Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone. |
− | [[File:Network RUTOS manual lan as wan firewall general.png|border|class=tlt-border|1102px]]
| |
− | ----
| |
| | | |
| In WAN zone settings | | In WAN zone settings |
| * Make sure that yours newly created interface is selected in Covered networks list. | | * Make sure that yours newly created interface is selected in Covered networks list. |
| * Click Save & Apply. | | * Click Save & Apply. |
− | [[File:Network RUTOS manual lan as wan firewall zone.png|border|class=tlt-border|1102px]] | + | [[File:Firewall zones.png|border|center|class=tlt-border|859x422px]] |
| | | |
| ==Check new WAN interface== | | ==Check new WAN interface== |