|
|
| Line 38: |
Line 38: |
| [[File:SSIDs General Settings_1.png|border|700x500px|class=tlt-border|center]] | | [[File:SSIDs General Settings_1.png|border|700x500px|class=tlt-border|center]] |
|
| |
|
| <ol>
| | ---- |
| <li>Open router‘s WebUI and navigate to '''Network''' → '''Wireless'''.</li>
| | In router‘s WebUI, Navigate to '''Network → Wireless section → SSIDs'''. click [[File:Add Button.png]] and create new interface. Frequency band must match in all nodes. |
| <li>Depending on your application requirements and availability, open 2.4GHz or 5GHz interface configuration. 2.4GHz is selected for this example.</li>
| | |
| <li>In '''General Setup''' tab make sure '''Mode''' is selected as '''Access Point'''.</li>
| | Make the following changes: |
| <li>Change SSID so that it would be '''the same in all of the routers'''.</li>
| | |
| <li>In '''Wireless Security''' tab select encryption and set Password so that it would be '''the same in all of the routers'''.</li>
| | # Select Mode: '''Mesh''' |
| <li>In router‘s WebUI, Navigate to '''Network''' → '''Wireless''' section. '''Add new''' 2.4GHZ or 5GHz interface. '''This frequency band must match in all routers'''. </li>
| | # Select Radios: '''2.4GHZ''' |
| <li>An interface configuration window will show up. In '''General Setup''' tab '''Enable''' interface, select Mode as '''Mesh''', and enter Mesh ID. '''Mesh ID Must be identical in all devices'''.</li>
| | # Enter SSID: '''Demo_1''' |
| <li>In '''Wireless Security''' tab select Encryption '''WPA3 – SAE''' and enter the Password. '''The password must match in all devices'''.</li>
| | # Enter Password: '''Password''' |
| <li>In '''Advanced Settings''' tab enable Forward mesh peer traffic and set RSSI threshold for joining to '''-80'''. Leave the rest as set by default.</li>
| | [[File:Mesh_General_Settings_1.png|border|700x500px|class=tlt-border|center]] |
| <li>Lastly, press '''Edit''' on general radio settings.</li>
| | |
| <li>Set wireless channel to use. Channel must be '''the same in all of the routers'''</li>
| | ---- |
| </ol>
| | Make the following changes in '''Mesh Additional''' settings tab: |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_common_configuration_1_v2.png|border|class=tlt-border]] | | # Enable Forward mesh peer traffic: '''on''' |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_common_configuration_2_v2.png|border|class=tlt-border]]
| | # Enter RSSI threshold for joining: '''-80''' |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_common_configuration_3_v2.png|border|class=tlt-border]]
| | [[File:Mesh Additional Settings.png|border|class=tlt-border|center]] |
| [[File:Networking rutx11 configuration example wireless mesh mesh common configuration 4 v2.png|border|class=tlt-border]]
| | |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_common_configuration_5_v2.png|border|class=tlt-border]]
| | ---- |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_common_configuration_6_v2.png|border|class=tlt-border]]
| | In router‘s WebUI, Navigate to '''Network → Wireless section → Radio → Wifi 2.4GHZ settings'''. |
| [[File:Networking rutx11 configuration example wireless mesh mesh common configuration 7 v2.png|border|class=tlt-border]] | | |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_demo_common_configuration_8.JPG|border|class=tlt-border]]
| | Make the following changes: |
| [[File:Networking_rutx11_configuration_example_wireless_mesh_mesh_demo_common_configuration_9.JPG|border|class=tlt-border]]
| | # Select Channel: '''11 (2462 Mhz)''' |
| | [[File:Mesh Channel Selection.png|border|700x500px|class=tlt-border|center]] |
|
| |
|
| ===Mesh nodes=== | | ===Mesh nodes=== |
