9,312
edits
Changes
Template:Networking rutos manual input output (view source)
Revision as of 18:43, 27 January 2022
, 18:43, 27 January 2022→Physical characteristics and I/O pin mapping
| configurableio = {{{configurableio}}}
| configurableio = {{{configurableio}}}
| input_volts = {{{input_volts}}}
| input_volts = {{{input_volts}}}
}}{{#switch: {{{name}}}
}}{{#switch: RUT955
| TRB141 =<h3>Input/Output Connector Pinout</h3>
| TRB141 =<h3>Input/Output Connector Pinout</h3>
----
----
[[File:Networking_trb141_manual_input_output_input_output_connector_pinout.png]]
[[File:Networking_trb141_manual_input_output_input_output_connector_pinout_v2.png]]
<ul>
<ul>
| RUT955|RUT956 =<h3>Input/Output Connector Pinout</h3>
| RUT955|RUT956 =<h3>Input/Output Connector Pinout</h3>
----
----
[[File:Networking_rut955_manual_input_output_input_output_connector_pinout.png]]
<ul>
<ul>
<li>Digital input (DIN1): Logic low 0 - 1.2 V; Logic high 1.8 - 3 V</li>
<li><b>DI</b><sub>1</sub> and <b>⏚</b><sub>1</sub> - Digital input:</li>
<li>Digital galvanically isolated input (DIN2): 0 - 30 V</li>
<ul>
<li>Analog input (voltage mode): 0 – 24 V<span class="asterisk">*</span></li>
<li>0-1.2 V is detected as logical "0"</li>
<li>Analog input (current mode): up to 20 mA (commonly used with 4-20 mA standard sensors)</li>
<li>1.8-3 V is detected as logical "1"</li>
<li>Digital open collector (OC) output: 30 V, 250 mA</li>
</ul>
<li>SPST relay output: 24 V, 4 A</li>
<li><b>DI</b><sub>2</sub> and <b>⏚</b><sub>2</sub> - Digital galvanically isolated input:</li>
<ul>
<li>0-4 V is detected as logical "0"</li>
<li>9-30 V is detected as logical "1"</li>
</ul>
<li><b>DO</b><sub>1</sub> and <b>⏚</b><sub>3</sub> - Galvanically isolated open collector (OC) output: 30 V, 250 mA</li>
<li><b>DO</b><sub>2</sub> and <b>⏚</b><sub>3</sub> - OC output: VCC 0-30 VDC.</li>
<li><b>C & NO</b> - Common and Normally Closed contacts of the internal Latching Relay respectively.<br>Maximum relay ratings: 4 A at 24 VDC, 4 A at 40 VAC.</li>
<li><b>A</b> and <b>⏚</b><sub>1</sub> - ADC input. Analog voltage range: 0-30 V. The input can be configured for 4-20 mA sensor protocol as current measurement (ACL).<span class="asterisk">*</span></li>
<li><b>⏚</b><sub>1</sub> - GND for <b>DI</b><sub>1</sub> and <b>A</b>.</li>
<li><b>⏚</b><sub>2</sub> - GND for <b>DI</b><sub>2</sub>.
<li><b>⏚</b><sub>3</sub> - GND for <b>DO</b>.
</ul>
</ul>
----
----
