Difference between revisions of "RUT850 Routing"
From Teltonika Networks Wiki
Line 11: | Line 11: | ||
[[Image:Network routing static routes.PNG]] | [[Image:Network routing static routes.PNG]] | ||
− | + | <table class="nd-mantable"> | |
− | + | <tr> | |
− | + | <th>field name</th> | |
− | + | <th>value</th> | |
− | + | <th>description</th> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>Routing table</td> | |
− | + | <td>Main {{!}} WAN {{!}} WAN2 {{!}} WAN3; Default: '''WAN'''</td> | |
− | + | <td>Defines which table will be used for the route in question</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>Interface</td> | |
− | + | <td>LAN {{!}} WAN(wired) {{!}} WAN2(Mobile) {{!}} WAN3(WiFi) {{!}} VPN instances; Default: '''WAN(wired)'''</td> | |
− | + | <td>The zone where the target network resides</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>Destination address'''*'''</td> | |
− | + | <td>ip; Default: '''0.0.0.0'''</td> | |
− | + | <td>The address of the destination network</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>Netmask'''*'''</td> | |
− | + | <td>ip; Default: '''0.0.0.0'''</td> | |
− | + | <td>A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>Gateway</td> | |
− | + | <td>ip; Default: " "</td> | |
− | + | <td>Defines where the router should send all the traffic that applies to the rule</td> | |
− | + | </tr> | |
+ | <tr> | ||
+ | <td>Metric</td> | ||
+ | <td>integer; Default: '''0'''</td> | ||
+ | <td>The '''Metric''' value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied</td> | ||
+ | </tr> | ||
+ | </table> | ||
'''*Additional notes on Destination & Netmask:''' | '''*Additional notes on Destination & Netmask:''' | ||
You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.: | You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.: | ||
− | + | <table class="nd-mantable"> | |
− | + | <tr> | |
− | + | <th>field name</th> | |
− | + | <th>value</th> | |
− | + | <th>description</th> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>192.168.55.161</td> | |
− | + | <td>255.255.255.255</td> | |
− | + | <td>Only applies to 192.168.55.161'''</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>192.168.55.0</td> | |
− | + | <td>255.255.255.240</td> | |
− | + | <td>Applies to IPs in the 192.168.55.0 - 192.168.55.255</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>192.168.55.240</td> | |
− | + | <td>255.255.255.240</td> | |
− | + | <td>192.168.55.240 - 192.168.55.255</td> | |
− | + | </tr> | |
− | + | <tr> | |
− | + | <td>192.168.55.161</td> | |
− | + | <td>255.255.255.0</td> | |
− | + | <td>192.168.55.0 - 192.168.55.255</td> | |
− | + | </tr> | |
− | + | <tr> | |
+ | <td>192.168.0.0</td> | ||
+ | <td>255.255.0.0</td> | ||
+ | <td>192.168.0.0 - 192.168.255.255</td> | ||
+ | </tr> | ||
+ | </table> |
Revision as of 08:45, 17 December 2018
Main Page > RUT Routers > RUT850 > RUT850 Manual > RUT850 WebUI > RUT850 Network section > RUT850 RoutingSummary
This chapter is an overview of the Routing section in RUT devices.
Static Routes
Static routes specify over which interface and gateway a certain host or network can be reached. In this page you can configure your own custom routes.
field name | value | description |
---|---|---|
Routing table | Main | WAN | WAN2 | WAN3; Default: WAN | Defines which table will be used for the route in question |
Interface | LAN | WAN(wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: WAN(wired) | The zone where the target network resides |
Destination address* | ip; Default: 0.0.0.0 | The address of the destination network |
Netmask* | ip; Default: 0.0.0.0 | A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies |
Gateway | ip; Default: " " | Defines where the router should send all the traffic that applies to the rule |
Metric | integer; Default: 0 | The Metric value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied |
*Additional notes on Destination & Netmask:
You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.:
field name | value | description |
---|---|---|
192.168.55.161 | 255.255.255.255 | Only applies to 192.168.55.161 |
192.168.55.0 | 255.255.255.240 | Applies to IPs in the 192.168.55.0 - 192.168.55.255 |
192.168.55.240 | 255.255.255.240 | 192.168.55.240 - 192.168.55.255 |
192.168.55.161 | 255.255.255.0 | 192.168.55.0 - 192.168.55.255 |
192.168.0.0 | 255.255.0.0 | 192.168.0.0 - 192.168.255.255 |