RUT240 VPN: Difference between revisions

From Teltonika Networks Wiki
VisualWikitext
No edit summary
No edit summary
Line 29: Line 29:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Enables the OpenVPN instance</td>
       <td>Enables the OpenVPN instance</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>TUN/TAP</td>
       <td>TUN/TAP</td>
       <td>TUN (tunnel) {{!}} TAP (bridged); Default: '''TUN (tunnel)'''</td>
       <td>TUN (tunnel) | TAP (bridged); Default: '''TUN (tunnel)'''</td>
       <td>OpenVPN interface type. '''TUN''' is most often in typical VPN connections, however, '''TAP''' is required in some Ethernet bridging configurations</td>
       <td>OpenVPN interface type. '''TUN''' is most often in typical VPN connections, however, '''TAP''' is required in some Ethernet bridging configurations</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Protocol</td>
     <td>Protocol</td>
         <td>UDP {{!}} TCP; Default: '''UDP'''</td>
         <td>UDP | TCP; Default: '''UDP'''</td>
         <td>The transfer protocol used by the OpenVPN connection. '''TCP''' is connection oriented – once a connection is established, data can be sent bidirectionally. '''UDP''' is a simpler, connectionless Internet protocol. '''UDP''' is usually faster but '''TCP''' has more security features. Choose the connection protocol according to your needs.</td>
         <td>The transfer protocol used by the OpenVPN connection. '''TCP''' is connection oriented – once a connection is established, data can be sent bidirectionally. '''UDP''' is a simpler, connectionless Internet protocol. '''UDP''' is usually faster but '''TCP''' has more security features. Choose the connection protocol according to your needs.</td>
     </tr>
     </tr>
Line 49: Line 49:
     <tr>
     <tr>
       <td>LZO</td>
       <td>LZO</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources</td>
       <td>With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Encryption</td>
       <td>Encryption</td>
       <td>DES-CBC 64 {{!}} RC2-CBC 128 {{!}} DES-EDE-CBC 128 {{!}} DES-EDE3-CBC 192 {{!}} DESX-CBC 192 {{!}} BF-CBC 128 {{!}} RC2-40-CBC 40 {{!}} CAST5-CBC 128 {{!}} RC2-40CBC 40 {{!}} CAST5-CBC 128 {{!}} RC2-64-CBC 64{{!}} AES-128-CBC 128 {{!}} AES-192-CBC 192 {{!}} AES-256-CBC 256 {{!}} none; Default: '''BF-CBC 128'''</td>
       <td>DES-CBC 64 | RC2-CBC 128 | DES-EDE-CBC 128 | DES-EDE3-CBC 192 | DESX-CBC 192 | BF-CBC 128 | RC2-40-CBC 40 | CAST5-CBC 128 | RC2-40CBC 40 | CAST5-CBC 128 | RC2-64-CBC 64| AES-128-CBC 128 | AES-192-CBC 192 | AES-256-CBC 256 | none; Default: '''BF-CBC 128'''</td>
       <td>Packet encryption algorithm</td>
       <td>Packet encryption algorithm</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Authentication</td>
     <td>Authentication</td>
         <td>TLS {{!}} Static Key {{!}} Password {{!}} TLS/Password; Default: '''TLS'''</td>
         <td>TLS | Static Key | Password | TLS/Password; Default: '''TLS'''</td>
         <td>Authentication mode, used to secure data sessions.
         <td>Authentication mode, used to secure data sessions.
'''Static key''' is a secret key used for server–client authentication.
'''Static key''' is a secret key used for server–client authentication.
Line 75: Line 75:
     <tr>
     <tr>
     <td>TLS cipher</td>
     <td>TLS cipher</td>
         <td>all {{!}} DHE+RSA {{!}} custom; Default: '''all'''</td>
         <td>all | DHE+RSA | custom; Default: '''all'''</td>
         <td>Packet encryption algorithm cipher</td>
         <td>Packet encryption algorithm cipher</td>
     </tr>
     </tr>
Line 85: Line 85:
     <tr>
     <tr>
       <td>Resolve retry</td>
       <td>Resolve retry</td>
       <td>integer {{!}} infinite; Default: '''infinite'''</td>
       <td>integer | infinite; Default: '''infinite'''</td>
       <td>Time in seconds to resolve server hostname periodically in case of first resolve failure before generating service exception</td>
       <td>Time in seconds to resolve server hostname periodically in case of first resolve failure before generating service exception</td>
     </tr>
     </tr>
Line 121: Line 121:
     <tr>
     <tr>
     <td>HMAC authentication algorithm</td>
     <td>HMAC authentication algorithm</td>
         <td>none {{!}} SHA1 {{!}} SHA256 {{!}} SHA384 {{!}} SHA512; Default: '''SHA1'''</td>
         <td>none | SHA1 | SHA256 | SHA384 | SHA512; Default: '''SHA1'''</td>
         <td>HMAC authentication algorithm type</td>
         <td>HMAC authentication algorithm type</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Additional HMAC authentication</td>
       <td>Additional HMAC authentication</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>An additional layer of HMAC authentication on top of the TLS control channel to protect against DoS attacks</td>
       <td>An additional layer of HMAC authentication on top of the TLS control channel to protect against DoS attacks</td>
     </tr>
     </tr>
Line 169: Line 169:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Enables the OpenVPN instance</td>
       <td>Enables the OpenVPN instance</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>TUN/TAP</td>
       <td>TUN/TAP</td>
       <td>TUN (tunnel) {{!}} TAP (bridged); Default: '''TUN (tunnel)'''</td>
       <td>TUN (tunnel) | TAP (bridged); Default: '''TUN (tunnel)'''</td>
       <td>OpenVPN interface type. '''TUN''' is most often in typical VPN connections, however, '''TAP''' is required in some Ethernet bridging configurations</td>
       <td>OpenVPN interface type. '''TUN''' is most often in typical VPN connections, however, '''TAP''' is required in some Ethernet bridging configurations</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Protocol</td>
     <td>Protocol</td>
         <td>UDP {{!}} TCP; Default: '''UDP'''</td>
         <td>UDP | TCP; Default: '''UDP'''</td>
         <td>The transfer protocol used by the OpenVPN connection. '''TCP''' is connection oriented – once a connection is established, data can be sent bidirectionally. '''UDP''' is a simpler, connectionless Internet protocol. '''UDP''' is usually faster but '''TCP''' has more security features. Choose the connection protocol according to your needs.</td>
         <td>The transfer protocol used by the OpenVPN connection. '''TCP''' is connection oriented – once a connection is established, data can be sent bidirectionally. '''UDP''' is a simpler, connectionless Internet protocol. '''UDP''' is usually faster but '''TCP''' has more security features. Choose the connection protocol according to your needs.</td>
     </tr>
     </tr>
Line 189: Line 189:
     <tr>
     <tr>
       <td>LZO</td>
       <td>LZO</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources</td>
       <td>With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Encryption</td>
       <td>Encryption</td>
       <td>DES-CBC 64 {{!}} RC2-CBC 128 {{!}} DES-EDE-CBC 128 {{!}} DES-EDE3-CBC 192 {{!}} DESX-CBC 192 {{!}} BF-CBC 128 {{!}} RC2-40-CBC 40 {{!}} CAST5-CBC 128 {{!}} RC2-40CBC 40 {{!}} CAST5-CBC 128 {{!}} RC2-64-CBC 64{{!}} AES-128-CBC 128 {{!}} AES-192-CBC 192 {{!}} AES-256-CBC 256 {{!}} none; Default: '''BF-CBC 128'''</td>
       <td>DES-CBC 64 | RC2-CBC 128 | DES-EDE-CBC 128 | DES-EDE3-CBC 192 | DESX-CBC 192 | BF-CBC 128 | RC2-40-CBC 40 | CAST5-CBC 128 | RC2-40CBC 40 | CAST5-CBC 128 | RC2-64-CBC 64| AES-128-CBC 128 | AES-192-CBC 192 | AES-256-CBC 256 | none; Default: '''BF-CBC 128'''</td>
       <td>Packet encryption algorithm</td>
       <td>Packet encryption algorithm</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Authentication</td>
     <td>Authentication</td>
         <td>TLS'''*''' {{!}} Static Key {{!}} Password {{!}} TLS/Password; Default: '''TLS'''</td>
         <td>TLS'''*''' | Static Key | Password | TLS/Password; Default: '''TLS'''</td>
         <td>Authentication mode, used to secure data sessions.
         <td>Authentication mode, used to secure data sessions.
'''Static key''' is a secret key used for server–client authentication.
'''Static key''' is a secret key used for server–client authentication.
Line 215: Line 215:
     <tr>
     <tr>
     <td>TLS cipher</td>
     <td>TLS cipher</td>
         <td>all {{!}} DHE+RSA {{!}} custom; Default: '''all'''</td>
         <td>all | DHE+RSA | custom; Default: '''all'''</td>
         <td>Packet encryption algorithm cipher</td>
         <td>Packet encryption algorithm cipher</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Client to client</td>
       <td>Client to client</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Enables client to client communication in the Virtual network. In order for Client to client to work, the TLS Clients section most be utilized</td>
       <td>Enables client to client communication in the Virtual network. In order for Client to client to work, the TLS Clients section most be utilized</td>
     </tr>
     </tr>
Line 246: Line 246:
     <tr>
     <tr>
       <td>Allow duplicate certificates</td>
       <td>Allow duplicate certificates</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>If checked, the server allows clients to connect with identical certificates</td>
       <td>If checked, the server allows clients to connect with identical certificates</td>
     </tr>
     </tr>
Line 351: Line 351:
     <tr>
     <tr>
     <td>Enable</td>
     <td>Enable</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Toggles the IPsec instance ON or OFF</td>
         <td>Toggles the IPsec instance ON or OFF</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>IKE version</td>
     <td>IKE version</td>
         <td>IKEv1 {{!}} IKEv2; Default: '''IKEv1'''</td>
         <td>IKEv1 | IKEv2; Default: '''IKEv1'''</td>
         <td>Method of key exchange</td>
         <td>Method of key exchange</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Mode</td>
       <td>Mode</td>
       <td>Main {{!}} Aggressive; Default: '''Main'''</td>
       <td>Main | Aggressive; Default: '''Main'''</td>
       <td>ISAKMP phase 1 exchange mode</td>
       <td>ISAKMP phase 1 exchange mode</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Type</td>
       <td>Type</td>
       <td>Tunnel {{!}} Transport; Default: '''Tunnel'''</td>
       <td>Tunnel | Transport; Default: '''Tunnel'''</td>
       <td>Type of connection. <br> '''Tunnel''': protects the internal routing information by encrypting the IP header of the original packet. The original packet is encapsulated by a another set of IP headers. NAT traversal is supported with the tunnel mode. <br> '''Transport''': encrypts only the payload and Encapsulating Security Payload (ESP) trailer; so the IP header of the original packet is not encrypted. Transport mode is usually used when another tunneling protocol (such as [[RUT240 VPN#GRE_Tunnel|GRE]], [[RUT240 VPN#L2TP|L2TP]] (click '''[[L2TP over IPsec|here]]''' for a configuration example on '''L2TP over IPsec''')) is used to first encapsulate the IP data packet, then IPsec is used to protect the GRE/L2TP tunnel packets. NAT traversal is not supported with the transport mode.</td>
       <td>Type of connection. <br> '''Tunnel''': protects the internal routing information by encrypting the IP header of the original packet. The original packet is encapsulated by a another set of IP headers. NAT traversal is supported with the tunnel mode. <br> '''Transport''': encrypts only the payload and Encapsulating Security Payload (ESP) trailer; so the IP header of the original packet is not encrypted. Transport mode is usually used when another tunneling protocol (such as [[RUT240 VPN#GRE_Tunnel|GRE]], [[RUT240 VPN#L2TP|L2TP]] (click '''[[L2TP over IPsec|here]]''' for a configuration example on '''L2TP over IPsec''')) is used to first encapsulate the IP data packet, then IPsec is used to protect the GRE/L2TP tunnel packets. NAT traversal is not supported with the transport mode.</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>My identifier type</td>
     <td>My identifier type</td>
         <td>Address {{!}} FQDN {{!}} User FQDN; Default: '''FQDN'''</td>
         <td>Address | FQDN | User FQDN; Default: '''FQDN'''</td>
         <td>Type of connection</td>
         <td>Type of connection</td>
     </tr>
     </tr>
Line 381: Line 381:
     <tr>
     <tr>
       <td>Local IP address/Subnet mask</td>
       <td>Local IP address/Subnet mask</td>
       <td>ip/netmask {{!}} Default: " "</td>
       <td>ip/netmask | Default: " "</td>
       <td>Local network secure group IP address and mask used to determine at what subnet an IP address can be accessed. Netmask range [0 - 32]. If left empty IP address will be selected automatically</td>
       <td>Local network secure group IP address and mask used to determine at what subnet an IP address can be accessed. Netmask range [0 - 32]. If left empty IP address will be selected automatically</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Left firewall</td>
       <td>Left firewall</td>
       <td>yes {{!}} no; Default: '''yes'''</td>
       <td>yes | no; Default: '''yes'''</td>
       <td>Excludes IPsec tunnel from firewall rules</td>
       <td>Excludes IPsec tunnel from firewall rules</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Force encapsulation</td>
     <td>Force encapsulation</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Forces UDP encapsulation for ESP packets even if no NAT situation is detected</td>
         <td>Forces UDP encapsulation for ESP packets even if no NAT situation is detected</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Dead Peer Detection</td>
     <td>Dead Peer Detection</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>The values 'clear', 'hold' and 'restart' all activate DPD</td>
         <td>The values 'clear', 'hold' and 'restart' all activate DPD</td>
     </tr>
     </tr>
Line 406: Line 406:
     <tr>
     <tr>
       <td>Remote VPN endpoint</td>
       <td>Remote VPN endpoint</td>
       <td>host {{!}} ip; Default: " "</td>
       <td>host | ip; Default: " "</td>
       <td>IP address or hostname of the remote IPsec instance</td>
       <td>IP address or hostname of the remote IPsec instance</td>
     </tr>
     </tr>
Line 416: Line 416:
     <tr>
     <tr>
     <td>Right firewall</td>
     <td>Right firewall</td>
         <td>yes {{!}} no; Default: '''yes'''</td>
         <td>yes | no; Default: '''yes'''</td>
         <td>Excludes remote side IPsec tunnel from firewall rules</td>
         <td>Excludes remote side IPsec tunnel from firewall rules</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Enable keep alive</td>
       <td>Enable keep alive</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles the tunnel's keep alive function ON or OFF. When enabled, the instance sends ICMP packets to the specified host at the specified frequency. If no response is received, the instance attempts to restart the connection</td>
       <td>Toggles the tunnel's keep alive function ON or OFF. When enabled, the instance sends ICMP packets to the specified host at the specified frequency. If no response is received, the instance attempts to restart the connection</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Host</td>
       <td>Host</td>
       <td>host {{!}} ip; Default: " "</td>
       <td>host | ip; Default: " "</td>
       <td>Hostname or IP address to which ICMP packets will be sent to. Best to use a hostname/IP address belonging to the opposite instance's LAN</td>
       <td>Hostname or IP address to which ICMP packets will be sent to. Best to use a hostname/IP address belonging to the opposite instance's LAN</td>
     </tr>
     </tr>
Line 436: Line 436:
     <tr>
     <tr>
     <td>Allow WebUI access</td>
     <td>Allow WebUI access</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Allows WebUI access for hosts from the opposite instance</td>
         <td>Allows WebUI access for hosts from the opposite instance</td>
     </tr>
     </tr>
Line 456: Line 456:
     <tr>
     <tr>
       <td>Encryption algorithm</td>
       <td>Encryption algorithm</td>
       <td>DES {{!}} 3DES {{!}} AES 128 {{!}} AES 192 {{!}} AES256; Default: '''3DES'''</td>
       <td>DES | 3DES | AES 128 | AES 192 | AES256; Default: '''3DES'''</td>
       <td>The encryption algorithm must match with another incoming connection</td>
       <td>The encryption algorithm must match with another incoming connection</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Authentication</td>
       <td>Authentication</td>
       <td>MD5 {{!}} SHA1 {{!}} SHA256 {{!}} SHA384 {{!}} SHA512; Default: '''SHA1'''</td>
       <td>MD5 | SHA1 | SHA256 | SHA384 | SHA512; Default: '''SHA1'''</td>
       <td>The authentication algorithm must match with another incoming connection</td>
       <td>The authentication algorithm must match with another incoming connection</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Has algorithm</td>
     <td>Has algorithm</td>
         <td>MD5 {{!}} SHA1 {{!}} SHA256 {{!}} SHA384 {{!}} SHA512; Default: '''SHA1'''</td>
         <td>MD5 | SHA1 | SHA256 | SHA384 | SHA512; Default: '''SHA1'''</td>
         <td>The hash algorithm must match with another incoming connection</td>
         <td>The hash algorithm must match with another incoming connection</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>DH group</td>
     <td>DH group</td>
         <td>MODP768 {{!}} MODP1024 {{!}} MODP1536 {{!}} MODP2048 {{!}} MODP3072 {{!}} MODP4096; Default: '''MODP1536'''</td>
         <td>MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096; Default: '''MODP1536'''</td>
         <td>The DH (Diffie-Helman) group must match with another incoming connection</td>
         <td>The DH (Diffie-Helman) group must match with another incoming connection</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>PFS group</td>
     <td>PFS group</td>
         <td>MODP768 {{!}} MODP1024 {{!}} MODP1536 {{!}} MODP2048 {{!}} MODP3072 {{!}} MODP4096 {{!}} No PFS; Default: '''MODP1536'''</td>
         <td>MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096 | No PFS; Default: '''MODP1536'''</td>
         <td>The PFS (Perfect Forward Secrecy) group must match with another incoming connection</td>
         <td>The PFS (Perfect Forward Secrecy) group must match with another incoming connection</td>
     </tr>
     </tr>
Line 513: Line 513:
     <tr>
     <tr>
       <td>Enabled</td>
       <td>Enabled</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles GRE Tunnel ON or OFF</td>
       <td>Toggles GRE Tunnel ON or OFF</td>
     </tr>
     </tr>
Line 548: Line 548:
     <tr>
     <tr>
     <td>PMTUD</td>
     <td>PMTUD</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Toggles the Path Maximum Transmission Unit Discovery (PMTUD) status on this tunnel ON or OFF</td>
         <td>Toggles the Path Maximum Transmission Unit Discovery (PMTUD) status on this tunnel ON or OFF</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Redirect LAN to GRE</td>
       <td>Redirect LAN to GRE</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Redirects LAN traffic to the GRE interface</td>
       <td>Redirects LAN traffic to the GRE interface</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Enable Keep alive</td>
       <td>Enable Keep alive</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Gives the ability for one side to originate and receive keep alive packets to and from a remote router</td>
       <td>Gives the ability for one side to originate and receive keep alive packets to and from a remote router</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Keep Alive host</td>
     <td>Keep Alive host</td>
         <td>host {{!}} ip; Default: " "</td>
         <td>host | ip; Default: " "</td>
         <td>Keep Alive IP address to send pings to. Preferably this should be an IP address which belongs to the LAN network on the remote device</td>
         <td>Keep Alive IP address to send pings to. Preferably this should be an IP address which belongs to the LAN network on the remote device</td>
     </tr>
     </tr>
Line 596: Line 596:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles PPTP Client ON or OFF</td>
       <td>Toggles PPTP Client ON or OFF</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Use as default gateway</td>
       <td>Use as default gateway</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Use this PPTP instance as default gateway</td>
       <td>Use this PPTP instance as default gateway</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Client to client</td>
     <td>Client to client</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Toggles client to client on the PPTP tunnel ON or OFF</td>
         <td>Toggles client to client on the PPTP tunnel ON or OFF</td>
     </tr>
     </tr>
     <tr>
     <tr>
     <td>Server</td>
     <td>Server</td>
         <td>host {{!}} ip; Default: " "</td>
         <td>host | ip; Default: " "</td>
         <td>PPTP server's IP address or hostname</td>
         <td>PPTP server's IP address or hostname</td>
     </tr>
     </tr>
Line 638: Line 638:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles PPTP Server ON or OFF</td>
       <td>Toggles PPTP Server ON or OFF</td>
     </tr>
     </tr>
Line 694: Line 694:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles L2TP Client ON or OFF</td>
       <td>Toggles L2TP Client ON or OFF</td>
     </tr>
     </tr>
     <tr>
     <tr>
       <td>Server</td>
       <td>Server</td>
       <td>host {{!}} ip; Default: " "</td>
       <td>host | ip; Default: " "</td>
       <td>L2TP server's remote IP address or hostname</td>
       <td>L2TP server's remote IP address or hostname</td>
     </tr>
     </tr>
Line 726: Line 726:
     <tr>
     <tr>
       <td>Enable</td>
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''no'''</td>
       <td>yes | no; Default: '''no'''</td>
       <td>Toggles L2TP Server ON or OFF</td>
       <td>Toggles L2TP Server ON or OFF</td>
     </tr>
     </tr>
Line 809: Line 809:
     <tr>
     <tr>
         <td>Enabled</td>
         <td>Enabled</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Enables the Stunnel configuration.</td>
         <td>Enables the Stunnel configuration.</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <td>Operating Mode</td>
         <td>Operating Mode</td>
         <td>Client {{!}} Server; Default: ""</td>
         <td>Client | Server; Default: ""</td>
         <td>Specifies whether this configuration will be used for Stunnel client or server.</td>
         <td>Specifies whether this configuration will be used for Stunnel client or server.</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <td>Listen IP</td>
         <td>Listen IP</td>
         <td>ip {{!}} host; Default: ""</td>
         <td>ip | host; Default: ""</td>
         <td>'''OPTIONAL'''
         <td>'''OPTIONAL'''


Line 838: Line 838:
     <tr>
     <tr>
         <td>TLS Cipher</td>
         <td>TLS Cipher</td>
         <td>None {{!}} Secure {{!}} Custom</td>
         <td>None | Secure | Custom</td>
         <td>Select permitted TLS ciphers (TLSv1.2 and below). If custom is selected, a new field appears to enter custom ciphers.</td>
         <td>Select permitted TLS ciphers (TLSv1.2 and below). If custom is selected, a new field appears to enter custom ciphers.</td>
     </tr>
     </tr>
Line 850: Line 850:
     <tr>
     <tr>
         <td>Application Protocol</td>
         <td>Application Protocol</td>
         <td>Not specified {{!}} Connect {{!}} SMTP; Default: '''Not specified'''</td>
         <td>Not specified | Connect | SMTP; Default: '''Not specified'''</td>
         <td>'''CLIENT SIDE ONLY'''
         <td>'''CLIENT SIDE ONLY'''


Line 859: Line 859:
     <tr>
     <tr>
         <td>Protocol Authentication</td>
         <td>Protocol Authentication</td>
         <td>'''Connect:''' Basic {{!}} NTLM; Default: '''Basic'''
         <td>'''Connect:''' Basic | NTLM; Default: '''Basic'''


             '''SMTP:''' Plain {{!}} Login; Default: '''Plain'''</td>
             '''SMTP:''' Plain | Login; Default: '''Plain'''</td>
         <td>'''CLIENT SIDE ONLY'''
         <td>'''CLIENT SIDE ONLY'''


Line 908: Line 908:
     <tr>
     <tr>
         <td>Verification</td>
         <td>Verification</td>
         <td>None {{!}} Verify Chain {{!}} Verify Peer; Default: '''None'''</td>
         <td>None | Verify Chain | Verify Peer; Default: '''None'''</td>
         <td>Verification type. '''Verify Chain''' verifies connections against a Certificate Authority (CA) file, while '''Verify Peer''' verifies connections against a list of approved certificates.</td>
         <td>Verification type. '''Verify Chain''' verifies connections against a Certificate Authority (CA) file, while '''Verify Peer''' verifies connections against a list of approved certificates.</td>
     </tr>
     </tr>
Line 964: Line 964:
     <tr>
     <tr>
         <td>Enabled</td>
         <td>Enabled</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Enables/activates all the enabled Stunnel configurations.</td>
         <td>Enables/activates all the enabled Stunnel configurations.</td>
     </tr>
     </tr>
Line 976: Line 976:
     <tr>
     <tr>
         <td>Use alternative config</td>
         <td>Use alternative config</td>
         <td>yes {{!}} no; Default: '''no'''</td>
         <td>yes | no; Default: '''no'''</td>
         <td>Enable alternative configuration option (Config upload).
         <td>Enable alternative configuration option (Config upload).
          
          
Line 1,016: Line 1,016:
** [[OpenVPN traffic split]]
** [[OpenVPN traffic split]]
** [[OpenVPN client on Windows]]
** [[OpenVPN client on Windows]]
[[Category:RUT240 WebUI]]

Revision as of 08:21, 1 March 2019

Main Page > EOL Products > RUT240 > RUT240 Manual > RUT240 WebUI > RUT240 Services section > RUT240 VPN

Summary

Virtual Private Network (VPN) is a method for secure data transfer through unsafe public networks. This page is an overview of different types of VPNs that can be used with RUT routers.

OpenVPN

OpenVPN is an open-source software application that implements virtual private network (VPN) techniques for creating secure point-to-point or site-to-site connections in routed or bridged configurations and remote access facilities. This section is an overview of the OpenVPN section of RUTxxx routers. For a more in depth guide refer to our OpenVPN configuration examples page.

The default OpenVPN Configuration list is empty, so you have to define your own configuration to establish any sort of OpenVPN connection. OpenVPN configurations can have one of two roles: client or server. Let’s start with an OpenVPN client. To create it, enter the desired instance name in the New configuration name field, select the instance’s role from the Role list and press the Add New button.

Once you’ve added a new OpenVPN instance there is no need to press the Save button, since the Add New button both creates and saves the new instance. By default the instance will be disabled and unconfigured. In order to establish an OpenVPN connection you must Enable your instance, enter an OpenVPN server address, choose an authentication method and a few other things, all of which can be configured in the Settings window, which can reached by pressing the Edit button next to your OpenVPN instance (as shown in the figure above).

OpenVPN Client

This section is overview of OpenVPN Client configuration.

The figure above is an example of a configured OpenVPN Client instance that uses the UDP protocol and TLS/Password authentication. Comprehensible explanations on how to configure each field are presented in the table below.

field name value description
Enable yes | no; Default: no Enables the OpenVPN instance
TUN/TAP TUN (tunnel) | TAP (bridged); Default: TUN (tunnel) OpenVPN interface type. TUN is most often in typical VPN connections, however, TAP is required in some Ethernet bridging configurations
Protocol UDP | TCP; Default: UDP The transfer protocol used by the OpenVPN connection. TCP is connection oriented – once a connection is established, data can be sent bidirectionally. UDP is a simpler, connectionless Internet protocol. UDP is usually faster but TCP has more security features. Choose the connection protocol according to your needs.
Port integer [0..65535]; Default: 1194 TCP/UDP Port number for both local and remote endpoints (make sure that the chosen port is allowed by firewall)
LZO yes | no; Default: no With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources
Encryption DES-CBC 64 | RC2-CBC 128 | DES-EDE-CBC 128 | DES-EDE3-CBC 192 | DESX-CBC 192 | BF-CBC 128 | RC2-40-CBC 40 | CAST5-CBC 128 | RC2-40CBC 40 | CAST5-CBC 128 | RC2-64-CBC 64| AES-128-CBC 128 | AES-192-CBC 192 | AES-256-CBC 256 | none; Default: BF-CBC 128 Packet encryption algorithm
Authentication TLS | Static Key | Password | TLS/Password; Default: TLS Authentication mode, used to secure data sessions.

Static key is a secret key used for server–client authentication.

TLS authentication mode uses X.509 type certificates:

Certificate Authority (CA), Client certificate, Client key.

All mentioned certificates can be generated using OpenVPN or Open SSL utilities on any type of host machine.

Password is a simple username/password based authentication where the owner of the OpenVPN server provides the login data.

TLS/Password uses both TLS and Password authentication
TLS cipher all | DHE+RSA | custom; Default: all Packet encryption algorithm cipher
Remote host / IP address ip; Default: " " IP address or hostname of an OpenVPN server
Resolve retry integer | infinite; Default: infinite Time in seconds to resolve server hostname periodically in case of first resolve failure before generating service exception
Keep alive integer *space* integer; Default: " " Defines two time intervals: one is used to periodically send ICMP request to the OpenVPN server, the other defines a time window, which is used to restart the OpenVPN service, if no ICMP response is received during the window time slice.
Example: 10 60
Remote network IP address ip; Default: " " LAN IP address of the remote network (server)
Remote network IP netmask ip; Default: " " LAN IP subnet mask of the remote network (server)
Username string; Default: " " User name used for authentication
Password string; Default: " " Password name used for authentication
Extra options string; Default: " " Extra options to be used by the OpenVPN instance
HMAC authentication algorithm none | SHA1 | SHA256 | SHA384 | SHA512; Default: SHA1 HMAC authentication algorithm type
Additional HMAC authentication yes | no; Default: no An additional layer of HMAC authentication on top of the TLS control channel to protect against DoS attacks
Certificate authority .ca file; Default: " " Certificate authority is an entity that issues digital certificates. A digital certificate certifies the ownership of a public key by the named subject of the certificate
Client certificate .crt file; Default: " " Client certificate is a type of digital certificate that is used by client systems to make authenticated requests to a remote server. Client certificates play a key role in many mutual authentication designs, providing strong assurances of a requester's identity
Client key .key file; Default: " " Authenticates the client to the server and establishes precisely who they are
Private key decryption password (optional) string; Default: " " Decrypts server private key password. Use only if server's .key file is encrypted with a password

After setting any of these parameters press the Save button or else the changes will not be applied. Some of the selected parameters will be shown in the configuration list table. You should also be aware of the fact that the router will launch a separate OpenVPN service for every configuration entry (if it is defined as active at the time, of course) so the router has the ability to act as server and client at the same time.

OpenVPN Server

This section is an overview of OpenVPN Server configuration.

The figure above is an example of a configured OpenVPN Server instance that uses the UDP protocol and TLS authentication. As you can see, the configuration is similar to OpenVPN Client but with a few key differences. Comprehensible explanations on each field are presented in the table below:

field name value description
Enable yes | no; Default: no Enables the OpenVPN instance
TUN/TAP TUN (tunnel) | TAP (bridged); Default: TUN (tunnel) OpenVPN interface type. TUN is most often in typical VPN connections, however, TAP is required in some Ethernet bridging configurations
Protocol UDP | TCP; Default: UDP The transfer protocol used by the OpenVPN connection. TCP is connection oriented – once a connection is established, data can be sent bidirectionally. UDP is a simpler, connectionless Internet protocol. UDP is usually faster but TCP has more security features. Choose the connection protocol according to your needs.
Port integer [0..65535]; Default: 1194 TCP/UDP Port number for both local and remote endpoints (make sure that the chosen port is allowed by firewall)
LZO yes | no; Default: no With LZO compression, your VPN connection will generate less network traffic. However, enabling this causes a higher CPU load. Use it carefully with a high traffic rate or low CPU resources
Encryption DES-CBC 64 | RC2-CBC 128 | DES-EDE-CBC 128 | DES-EDE3-CBC 192 | DESX-CBC 192 | BF-CBC 128 | RC2-40-CBC 40 | CAST5-CBC 128 | RC2-40CBC 40 | CAST5-CBC 128 | RC2-64-CBC 64| AES-128-CBC 128 | AES-192-CBC 192 | AES-256-CBC 256 | none; Default: BF-CBC 128 Packet encryption algorithm
Authentication TLS* | Static Key | Password | TLS/Password; Default: TLS Authentication mode, used to secure data sessions.

Static key is a secret key used for server–client authentication.

TLS authentication mode uses X.509 type certificates:

Certificate Authority (CA), Client certificate, Client key.

All mentioned certificates can be generated using OpenVPN or Open SSL utilities on any type of host machine.

Password is a simple username/password based authentication where the owner of the OpenVPN server provides the login data.

TLS/Password uses both TLS and Password authentication
TLS cipher all | DHE+RSA | custom; Default: all Packet encryption algorithm cipher
Client to client yes | no; Default: no Enables client to client communication in the Virtual network. In order for Client to client to work, the TLS Clients section most be utilized
Keep alive integer *space* integer; Default: " " efines two time intervals: one is used to periodically send ICMP request to the OpenVPN server, the other defines a time window, which is used to restart the OpenVPN service, if no ICMP response is received during the window time slice.
Example: 10 60
Virtual network IP address ip; Default: " " IP address of the Virtual network, e.g., 10.0.8.0
Virtual network IP netmask ip; Default: " " Subnet mask of the Virtual network
Push option string; Default: " " Push options are a way to “push” user defined routes to connecting clients’ routing tables. In the example above, the server will push the route of 192.168.1.0 network with the 255.255.255.0 netmask to connecting clients. Therefore, the client will be able to reach devices in the 192.168.1.0 network. This is useful when a client needs to reach devices located in the OpenVPN server’s LAN.
Allow duplicate certificates yes | no; Default: no If checked, the server allows clients to connect with identical certificates
Certificate authority .ca file; Default: " " Certificate authority is an entity that issues digital certificates. A digital certificate certifies the ownership of a public key by the named subject of the certificate
Server certificate .crt file; Default: " " Server certificate is a type of digital certificate that is used to identify the OpenVPN server
Server key .key file; Default: " " Authenticates clients to the server
Diffie Hellman parameters .pem file; Default: " " DH parameters define how OpenSSL performs the Diffie-Hellman (DH) key-exchange.

* You can find detailed instructions on how to generate your own TLS certificates here.

TLS Clients

TLS Clients is a way to more specifically differentiate clients by their Common Name (CN) found in the client certificate file. It can be used to assign specific VPN addresses to specific clients and bind them to their LAN addresses so that other device‘s in the client‘s LAN can be reached from the server or other clients.

The TLS Clients section can be found in the OpenVPN Server configuration window, provided that the OpenVPN server uses TLS or TLS/Password authentication methods. To create a new TLS client, type in the new client‘s name in the text field found bellow the TLS Clients tab and press the Add button.

field name value description
VPN instance name string; Default: " " With what VPN instance should the TLS Client be associated with
Endpoint name string; Default: " " Your endpoint name
Common name (CN) string; Default: " " Client’s Common Name (CN) found in the client’s certificate file
Virtual local endpoint ip; Default: " " Client’s virtual local address in the virtual network
Virtual remote endpoint ip; Default: " " Client’s virtual remote address in the virtual network
Private network ip; Default: " " Client’s private network (LAN) IP address
Private netmask ip; Default: " " Client’s private network (LAN) IP netmask

IPsec

The IPsec protocol client enables the router to establish a secure connection to an IPsec peer via the Internet. IPsec is supported in two modes - transport and tunnel. Transport mode creates a secure point to point channel between two hosts. Tunnel mode can be used to build a secure connection between two remote LANs serving as a VPN solution.

IPsec system maintains two databases: Security Policy Database (SPD) which defines whether to apply IPsec to a packet or not and specify which/how IPsec-SA is applied and Security Association Database (SAD), which contains a Key of each IPsec-SA.

The establishment of the Security Association (IPsec-SA) between two peers is needed for IPsec communication. It can be done by using manual or automated configuration.

NOTE: the router starts establishing a tunnel when data is sent from the router to a remote site over the tunnel. The Keep Alive feature is used for automatic tunnel establishment.

For a more in-depth configuration example, visit the IPsec configuration examples page.

To create a new IPsec instance, go to the IPsec tab, type in a name for your new instance in the text field below the IPsec tab and press the Add button next to it.

NOTE: You can create a maximum of 5 IPsec instances.


field name value description
Enable yes | no; Default: no Toggles the IPsec instance ON or OFF
IKE version IKEv1 | IKEv2; Default: IKEv1 Method of key exchange
Mode Main | Aggressive; Default: Main ISAKMP phase 1 exchange mode
Type Tunnel | Transport; Default: Tunnel Type of connection.
Tunnel: protects the internal routing information by encrypting the IP header of the original packet. The original packet is encapsulated by a another set of IP headers. NAT traversal is supported with the tunnel mode.
Transport: encrypts only the payload and Encapsulating Security Payload (ESP) trailer; so the IP header of the original packet is not encrypted. Transport mode is usually used when another tunneling protocol (such as GRE, L2TP (click here for a configuration example on L2TP over IPsec)) is used to first encapsulate the IP data packet, then IPsec is used to protect the GRE/L2TP tunnel packets. NAT traversal is not supported with the transport mode.
My identifier type Address | FQDN | User FQDN; Default: FQDN Type of connection
My identifier string; Default: " " In case RUT has a Private IP, its identifier should be its own LAN network address. In this way, the Road Warrior approach is possible
Local IP address/Subnet mask ip/netmask | Default: " " Local network secure group IP address and mask used to determine at what subnet an IP address can be accessed. Netmask range [0 - 32]. If left empty IP address will be selected automatically
Left firewall yes | no; Default: yes Excludes IPsec tunnel from firewall rules
Force encapsulation yes | no; Default: no Forces UDP encapsulation for ESP packets even if no NAT situation is detected
Dead Peer Detection yes | no; Default: no The values 'clear', 'hold' and 'restart' all activate DPD
Pre-shared key string; Default: " " A shared password used for authentication between the peers
Remote VPN endpoint host | ip; Default: " " IP address or hostname of the remote IPsec instance
Remote IP address/subnet mask ip/integer [0..32]; Default: " " Remote network secure group IP address and mask used to determine to what subnet an IP address belongs to. Should differ from device’s LAN IP
Right firewall yes | no; Default: yes Excludes remote side IPsec tunnel from firewall rules
Enable keep alive yes | no; Default: no Toggles the tunnel's keep alive function ON or OFF. When enabled, the instance sends ICMP packets to the specified host at the specified frequency. If no response is received, the instance attempts to restart the connection
Host host | ip; Default: " " Hostname or IP address to which ICMP packets will be sent to. Best to use a hostname/IP address belonging to the opposite instance's LAN
Ping period (sec) integer [0..9999999]; Default: " " The period (in seconds) at which ICMP packets will be sent to the specified keep alive host
Allow WebUI access yes | no; Default: no Allows WebUI access for hosts from the opposite instance

Phase 1/Phase 2

Phase 1 and Phase 2 must be configured in accordance with the IPSec server configuration, thus algorithms, authentication and lifetimes of each phase must be identical.


field name value description
Encryption algorithm DES | 3DES | AES 128 | AES 192 | AES256; Default: 3DES The encryption algorithm must match with another incoming connection
Authentication MD5 | SHA1 | SHA256 | SHA384 | SHA512; Default: SHA1 The authentication algorithm must match with another incoming connection
Has algorithm MD5 | SHA1 | SHA256 | SHA384 | SHA512; Default: SHA1 The hash algorithm must match with another incoming connection
DH group MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096; Default: MODP1536 The DH (Diffie-Helman) group must match with another incoming connection
PFS group MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096 | No PFS; Default: MODP1536 The PFS (Perfect Forward Secrecy) group must match with another incoming connection
Lifetime time; Default: 8 hours Duration for the phase

GRE Tunnel

GRE (Generic Routing Encapsulation RFC2784) is a solution for tunneling RFC1812 private address-space traffic over an intermediate TCP/IP network such as the Internet. GRE tunneling does not use encryption it simply encapsulates data and sends it over the wide area network (WAN).


In the example network diagram two distant networks LAN1 and LAN2 are connected. To create A GRE tunnel the user must know the following parameters:

  • Source and destination IP addresses
  • Tunnel’s local IP address
  • Distant network’s IP address and Subnet mask

To create a new GRE instance, go to the GRE Tunnel tab, type in a name for your new instance in the text field below the GRE Tunnel tab and press the Add New button next to it. The newly created instance will be disabled and unconfigured. To configure it press the Edit button located next to it. This action will redirect you to the instance’s GRE Tunnel Configuration window.


field name value description
Enabled yes | no; Default: no Toggles GRE Tunnel ON or OFF
Remote endpoint IP address ip; Default: " " WAN IP address or hostname of the remote GRE Tunnel instance
Remote network integer [0..32]; Default: " " LAN IP address of the remote device
Remote network netmask integer [0..32]; Default: " " LAN netmask of the remote device
Local tunnel IP ip; Default: " " Local virtual IP address. Can’t be in the same subnet as LAN network
MTU integer [0..255]; Default: 255 Toggles the Path Maximum Transmission Unit Discovery (PMTUD) status on this tunnel ON or OFF
TTL integer [0..255]; Default: 255 Fixed time-to-live (TTL) value on tunneled packets. The 0 is a special value meaning that packets inherit the TTL value
PMTUD yes | no; Default: no Toggles the Path Maximum Transmission Unit Discovery (PMTUD) status on this tunnel ON or OFF
Redirect LAN to GRE yes | no; Default: no Redirects LAN traffic to the GRE interface
Enable Keep alive yes | no; Default: no Gives the ability for one side to originate and receive keep alive packets to and from a remote router
Keep Alive host host | ip; Default: " " Keep Alive IP address to send pings to. Preferably this should be an IP address which belongs to the LAN network on the remote device
Keep alive interval integer [0..255]; Default: " " Frequency at which ICMP packets are sent by the Keep Alive function (in seconds)

To find a more in-depth GRE Tunnel configuration example, visit this page

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a protocol (set of communication rules) that allows corporations to extend their own corporate network through private "tunnels" over the public Internet. Effectively, a corporation uses a wide-area network as a single large local area network. A company no longer needs to lease its own lines for wide-area communication but can securely use the public networks.

For a more in-depth configuration example, visit the PPTP configuration examples page.

PPTP Client

To create a new PPTP instance, go to the PPTP tab, select the Role (server or client) of your instance, type in a name in the New configuration name field and press the Add button next to it. The newly created instance will be disabled and unconfigured. To configure it click the Edit button located next to it. This action will redirect you to the instance’s PPTP Configuration window.


field name value description
Enable yes | no; Default: no Toggles PPTP Client ON or OFF
Use as default gateway yes | no; Default: no Use this PPTP instance as default gateway
Client to client yes | no; Default: no Toggles client to client on the PPTP tunnel ON or OFF
Server host | ip; Default: " " PPTP server's IP address or hostname
Username string; Default: " " User name for authorization with the server
Password string; Default: " " Password used for authorization with the server

PPTP Server

field name value description
Enable yes | no; Default: no Toggles PPTP Server ON or OFF
Local IP ip; Default: 192.168.0.1 Virtual IP Address of this PPTP server
Remote IP range begin ip; Default: 192.168.0.20 Client IP address leases beginning
Remote IP range end ip; Default: 192.168.0.30 Client IP address leases end
User name string; Default: youruser Client's user name used for authentication with this server
Password string; Default: yourpass Client's password used for authentication with this server
PPTP Client's IP ip; Default: " " Client’s IP address. Leave empty to assign a random IP from the IP range specified above

L2TP

In computer networking, Layer 2 Tunneling Protocol (L2TP) is a tunneling protocol used to support virtual private networks (VPNs). It is more secure than PPTP but, because it encapsulates the transferred date twice, but it is slower and uses more CPU power.

For a more in-depth configuration example, visit the L2TP configuration examples page.

L2TP Client

To create a new L2TP instance, go to the L2TP tab, select the Role (server or client) of your instance, type in a name in the New configuration name field and press the Add button next to it. The newly created instance will be disabled and unconfigured. To configure it press the Edit button located next to it. This action will redirect you to the instance’s L2TP Configuration window.


field name value description
Enable yes | no; Default: no Toggles L2TP Client ON or OFF
Server host | ip; Default: " " L2TP server's remote IP address or hostname
Username string; Default: " " User name used to authenticate you to the L2TP server
Password string; Default: " " Password used to authenticate you to the server

L2TP Server

field name value description
Enable yes | no; Default: no Toggles L2TP Server ON or OFF
Local IP ip; Default: 192.168.0.1 Virtual IP Address of this L2TP server
Remote IP range begin ip; Default: 192.168.0.20 Client IP address leases beginning
Remote IP range end ip; Default: 192.168.0.30 Client IP address leases end
User name string; Default: user Client's user name used for authentication with this server
Password string; Default: pass Client's password used for authentication with this server

Stunnel

Stunnel is an open-source multi-platform software application used to provide a TLS/SSL tunneling service for already existing clients and servers. Below is an overview of the Stunnel application and its WebUI configuration section implemented on RUTxxx routers. For in-depth examples please visit Stunnel page.

Here is an approximate visual representation of Stunnel connection:


Upon creation, Stunnel configuration will be empty. User is expected to define their own configuration using the created configuration template. Stunnel provided encryption and connection will only work with properly configured Stunnel server(s) and client(s).

Duplicate configuration names are not allowed.

Stunnel configuration list window is located at Services → VPN → Stunnel:

Services menu, VPN section:

Stunnel tab:


To create a new configuration, enter the desired name in field below all configuration list entries and click button Add:

Once you’ve added a new Stunnel configuration, it is automatically saved - no need to press the Save button.

By default the configuration will be disabled and unconfigured. You can change the configuration by clicking the Edit button and delete the configuration by clicking the Delete button.

To establish an Stunnel connection you must have configured and enabled Stunnel client and server instances on either same or different routers.

Stunnel Configuration

Default Stunnel configuration:


Stunnel configuration field explanation table:

Field Name Value Description
Enabled yes | no; Default: no Enables the Stunnel configuration.
Operating Mode Client | Server; Default: "" Specifies whether this configuration will be used for Stunnel client or server.
Listen IP ip | host; Default: "" OPTIONAL Specifies which IP address or host should Stunnel listen to. If left empty, defaults to localhost.
Listen Port port (integer [0..65535]); Default: "" Specifies TCP port which Stunnel should listen to. Port cannot be taken by another service!
Connect IP's [host:]port; Default: "" Uses the standard host:port convetion (e.g. 127.0.0.1:6001; localhost:6001). Host part can be emmited - empty host part defaults to localhost. Must contain at least one item. If multiple options are specified, remote address is chosen using a round-robin algorithm.
TLS Cipher None | Secure | Custom Select permitted TLS ciphers (TLSv1.2 and below). If custom is selected, a new field appears to enter custom ciphers.
Allowed TLS Ciphers Cipher[:Cipher]..; Default: "" Only appears if a Custom TLS Cipher is selected
A colon-delimited TLS cipher list (e.g. DES-CBC3-SHA:IDEA-CBC-MD5)
Application Protocol Not specified | Connect | SMTP; Default: Not specified CLIENT SIDE ONLY

This option enables initial, protocol-specific negotiation of the TLS encryption. The protocol option should not be used with TLS encryption on a separate port.

If Connect or SMTP is selected, more customization fields appear.
Protocol Authentication Connect: Basic | NTLM; Default: Basic SMTP: Plain | Login; Default: Plain CLIENT SIDE ONLY

Options depend on the selected protocol

Authentication type for the protocol negotiations.
Protocol Domain domain (text); Default: "" CLIENT SIDE ONLY

Only appears if a Connect protocol is selected

Domain for the protocol negotiations.
Protocol Host host:port; Default: "" CLIENT SIDE ONLY

Only appears if a Connect protocol is selected

Destination address for the protocol negotiations.

Specifies the final TLS server to be connected to by the proxy, and not the proxy server directly connected by Stunnel. The proxy server should be specified with the connect option.
Protocol Username username (text); Default: "" CLIENT SIDE ONLY

Only appears if a protocol is selected

Username for the protocol negotiations.
Protocol Password password (text); Default: "" CLIENT SIDE ONLY

Only appears if a protocol is selected

Password for the protocol negotiations.
Verification None | Verify Chain | Verify Peer; Default: None Verification type. Verify Chain verifies connections against a Certificate Authority (CA) file, while Verify Peer verifies connections against a list of approved certificates.
Verification file file; Default: "" Only appears if a verification type is selected

File which is used to verify peer(s) or a peer chain. A different type of file is expected depending on the verification type selected:

Verify Chain: Expects a CA (Certificate Authority) file.

Verify Peer: Expects a file with one (or more, concatenated) peer certificate(s).
Certificate File file; Default: "" Mandatory for a server configuration. Optional for a client configuration

The parameter specifies the file containing certificates used by stunnel to authenticate itself against the remote client or server.

The file should contain the whole certificate chain starting from the actual server/client certificate, and ending with the self-signed root CA certificate.

Can be a certificate only, or both certificate and private key concatenated into a single file.
Private Key file; Default: Certificate File Can be skipped if the Certificate File is appended with the private key

Must be uploaded if the Certificate File does not contain the private key

A private key, required to authenticate the certificate owner.

After setting the parameters, click the Save button; otherwise, changes will not be saved. Some parameters will be shown in the configuration list table.


Stunnel Global Configuration

Default Stunnel global configuration:


Stunnel global configuration field explanation table:

Field Name Value Description
Enabled yes | no; Default: no Enables/activates all the enabled Stunnel configurations.
Debug Level integer [0..7]; Default: 5 Debugging level. Level is one of the syslog level names or numbers emerg (0), alert (1), crit (2), err (3), warning (4), notice (5), info (6), or debug (7). All logs for the specified level and all levels numerically less than it will be shown. Use 7 for greatest debugging output.
Use alternative config yes | no; Default: no Enable alternative configuration option (Config upload). Be aware that when using alternative configuration, all configurations in Stunnel Configuration section will be skipped.
Upload alternative config file; Default: "" Only appears if the "Use alternative config" is enabled
Upload the alternative Stunnel configuration file.


IMPORTANT:

The router can have multiple configurations set up and enabled at the same time. Note that if at least one configuration is not set correctly, none of them will be enabled, despite the "Enabled" flag being marked.

Also, you must mark the global "Enabled" flag to actually enable all the individually marked configurations.

See also

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=RUT240_VPN&oldid=29181"